Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Airside Heat Transfer and Friction Characteristics for Enhanced Fin-and-tube Heat Exchanger with Hydrophilic Coating under Wet Conditions

Study on heat transfer and friction characteristics in fin-tube heat exchangers used for electrical machines cooling

Air-side Heat Transfer Characteristics under Wet Conditions at Lower Ambient Pressure of Fin-and-tube Heat Exchanger

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Thermal-hydraulic performance evaluation of airside of wavy fin compact heat exchangers under wet conditions

Influence of Surface Modification on the Transient Dehumidification Performance of Fin-and-tube Heat Exchanger

Performance of the frosting characteristics of fin-and-tube heat exchanger subject to superhydrophobic coating

Experimental and numerical study and comparison of performance for herringbone wavy fin and enhanced fin with convex-strips in fin-and-tube heat exchanger

Effect Of Corrugation Angle Of Fin On Performance Of A Wavy Finned Tube Heat Exchanger Under Constant Fan Power Condition

Airside Performances of Finned Eight-Tube Heat Exchangers

Thermal-hydraulic Performance of Super-Amphiphobic Louver-Fin Flat-Tube Heat Exchanger under Fouled Condition

Investigation of the condensation heat-transfer between the wet air and 3-D finned-tube heat exchanger surface with different anti-corrosion coatings

Research on the air-side thermal hydraulic performance of louvered fin and flat tube heat exchangers under low-pressure environment

Airside Fin Efficiencies for Finned-Tube Heat Exchangers with Forced Convection

Effect of partially wet-surface condition on the performance of fin-tube heat exchanger

Numerical studies on heat transfer and pressure drop characteristics of flat finned tube bundles with various fin materials

Numerical analysis on heat transfer enhancement of wavy fin-tube heat exchangers for air-conditioning applications

Heat Transfer and Pressure Drop Correlations for Compact Heat Exchangers with Multi-Region Louver Fins