Abstract:The tensile behavior of Ti6Al4V–5Cu alloy studied in the temperature range of 450–550 °C at the strain rate interval of 10 −3 -10 −1 s −1 . Alloy deformation behavior, microstructure evolution, and its relative internal structure changes due to deformation were investigated. The tensile behavior of the alloy had elucidated in terms of change in true stress-strain relationship. At 450 °C, the alloy showed the decrease of peak stress at the strain rate interval of 10 −3 -10 −2 s −1 , which suggests Ti6Al4V–5Cu plastic flow behavior, was quite different. The alloy exhibited an elongation (El) of 28% at 450 °C in a strain rate of 10 −3 s −1 . At 10 −3 s −1 , the El of the alloy decreased with the increase of forming temperature. However, at 10 −2 s −1 and 10 −1 s −1 , the El increased with the rising of temperature. Scanning electron microscope (SEM) was used to investigate the microstructure of Ti6Al4V–5Cu alloy. The alloy grain boundaries (GBs) were found as continuous and discontinuous structural features, especially the high angle grain boundaries (HAGBs). The GB feature has contributed to the initiation of micro-cracks because of the creation of weakest regions in the material during deformation. The nature of GB geometry has also a tremendous contribution to the workability of Ti6Al4V–5Cu alloy at low forming temperatures. The presence of a high amount (%) LAGBs and the serrated nature of HAGBs structures determined the pull to grain pieces. The deformation mechanism of the Ti6Al4V–5Cu alloy at low forming temperatures was accomplished initially by boundary serration phenomenon due to strain-induced GB migration related to heat treatment at low strain condition, then by initiation of recrystallized grains-triggered by the plasticity behavior of strain induced sub-boundaries, and finally by the development of deformed grains generated by the reduction in corrugation propensity of GBs due to high strain condition.

Shear deformation of a TiAl alloy during cyclic heat treatment

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

Investigation on the microstructure evolution and dynamic recrystallization mechanisms of TiAl alloy at elevated temperature

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature

Cyclic Deformation and Lattice Strain Distribution of High Nb Containing TiAl Alloy

In-situ observation microstructure evolution and growth kinetics of lamellar γ phases in Ti44Al alloy during heat treatment

Molecular dynamics simulations of TC4 titanium alloy with mechanical property calculations after various heat treatments.

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

Optimizing microstructure and mechanical properties of directionally solidified Ti44Al6Nb1Cr2V alloy by directional heat treatment

Effect of High Strain Rate on Adiabatic Shearing of α+β Dual-Phase Ti Alloy

Fabrication of single-crystal Fe-Mn-Al-Cu alloys by cyclic heat treatments

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Thermal Stability and Lattice Strain Evolution of High‐Nb‐Containing TiAl Alloy under Low‐Cycle‐Fatigue Loading

Shear Texture Formation during High-Strain Torsion of Titanium Aluminides

Effects of heat treatment on the microstructures and mechanical properties of as-cast Ti-45Al-2Nb-2Cr-(0.2, 0.5) C alloys

A quasi in-situ study on the work hardening and softening mechanisms of Ti–33Zr–12Al–6V alloy

High strain torsion of a TiAl-based alloy

Investigation of α phase evolution and tensile fracture behavior of Ti5Al2Sn2Zr4Mo4Cr alloy fabricated by directed energy deposition

Study on High-Temperature Flow Behavior and Substructure and Texture Evolution of TA15 Titanium Alloy