Abstract:To have a better understand of film cooling technique, many experiments to investigate parameters affecting the film cooling effectiveness and heat transfer have been conducted. In this kind of experiments, different sorts of coolant (CO2, N-2 and etc.) are often applied to match coolant-to-mainstream properties or use some measuring techniques. However, the application of those coolant probably leads to a similarity problem, as the properties of them are different from air coolant in real engine conditions. This study investigates the accuracy of six criteria for the film cooling effectiveness scaling which changes the coolant from air to CO2 based on both experimental and numerical method, to promote the similarity to air coolant of film cooling experiments using CO2 as coolant. The study conducted on the pressure side of 1st stage stator from E-3 aero engine. The mainstream inlet pressure and temperature of the experiment was 112kPa and 312K, respectively. Numerical simulations were conducted by solving the Reynolds Averaged Naiver-Stokes (RANS) equations and Re-Normalization Group (RNG) k-epsilon turbulence model. The effect of CO2 coolant on pressure side film cooling effectiveness was initially investigated, followed by the analysis of the accuracy for six scaling criteria. Finally, reasons leading to the deviation of scaling was studied. Both numerical and experimental results indicate that the application of CO2 coolant leads to an obvious reduction of eta(APS) at relatively low coolant mass flow rate. That effect almost disappears at high coolant mass flow rate. In the experiment, eta with the variation in VR has the highest Pearson correlation coefficient (R-p) between air and CO2 coolant at almost all measuring points on pressure side, illustrating VR criterion has the highest accuracy in the scaling which the coolant is changed from air to CO2. The cooling effectiveness deviation of VR criterion is lower than 3% at all coolant CO2 percentage(obtained from CFD results). The low specific heat capacity of CO2 will lead to a relatively faster decay of injection temperature compared with air, producing an adverse influence on cooling effectiveness. The high density of CO2 can increase attachment ability of injections(especially on mid-span of the blade) and form a similar cooling film state to the air coolant at higher coolant mass flow rate. The results of this study can be used to promote the accuracy of the experiment using CO2 as coolant at relatively low temperature conditions in terms of film cooling effectiveness and injection state(attachment or separation). (c) 2021 Elsevier Ltd. All rights reserved.

Research on Water Simulation Experiment of Spinning Rotor Degassing Process of Al-alloy

Purification of Al Alloys by Spinning Rotor Degassing

Progress on agitated apparatus for polymer devolatilization and its CFD simulation

Flow Field And Gas-Bubble Size Analysis In Water Model For The Process Of Aluminum Melt Degassing By Particle Image Velocimetry

Study on Degassing Technology of Al Alloys

The Design of A Degassing Pump Based on Numerical and Experimental Research

Purification Technology of Molten Aluminum

Theoretical Analysis And Experimental Study Of Spray Degassing Method

Optimizing degassing for particle-reinforced Al composite: Advanced ultrasonic-assisted argon treatment and numerical simulation insights

Motion and mass transfer models for single bubble in an aluminum melt under a compound field of ultrasonic and rotating flow

Effect of Rotating Gas Bubble Stirring Process Parameters on Purifying Effectiveness and Mechanical Properties of Sand-Cast Mg–10Gd–3Y–0.5Zr Alloy

Parameters of Manufacturing Al-Si Alloy Wires by In-rotating Liquid Spinning Process

Numerical Simulation on Dehydrogenation Behavior during Argon Blowing Enhanced Vacuum Refining Process of High-quality Steel

A New Porous Nozzle for Aluminum Melts Purification—Preparation and Mathematical–Physical Model

Technology of Purification Degassing Used in Aluminum Melt

WATER MODELING OF MOULD FILLING DURING SUCTION CASTING PROCESS OF AUTOMOTIVE EXHAUST VALVES OF Γ-Tial BASED ALLOYS

Purification of aluminium-silicon alloy by electromagnetic directional solidification: Degassing and grain refinement

Research on Melt Degassing Processes of High Conductivity Hard Drawn Aluminum Wire

Numerical modeling and simulation of water cooling-controlled solidification for aluminum alloy investment casting

Numerical and Experimental Study of Scaling Criteria Accuracy for Film Cooling Using CO2 Coolant

CFD Simulation of a Supercritical CO2 Rolling Rotor Expander for Waste Heat Recovery System of Engines