Abstract:Given the lightweight nature and excellent thermal conductivity of aluminum, it offers significant potential for light-weighting of phase-change cooling components. To further enhance the thermal performance of aluminumbased vapor chambers, this study utilized selective laser melting (SLM) to design and integrally manufacture the slightly oleophilic wick for the condenser of the aluminum-based vapor chamber, along with three different superoleophilic wick structures for the evaporator: the gyroid bionic composite porous wick vapor chamber (GBCPVC), the groove composite porous wick vapor chamber (GCPVC), and the uniform porous wick vapor chamber (UPVC). A water-cooling experimental setup was established, and the effects of wick structure, cooling water flow rate, and cooling water temperature on the maximum heat load, temperature uniformity, and thermal resistance of vapor chambers were systematically investigated. The results indicated that the gyroid bionic porous wick structure significantly enhanced the thermal performance of the vapor chamber. Under the same conditions, GBCPVC exhibited lower thermal resistance and superior temperature uniformity, achieving a higher heat load than GCPVC and UPVC. When the cooling water temperature was decreased, its maximum heat load significantly increased. Specifically, at 15 degrees C, the maximum heat load for GBCPVC reached 300 W, an increase of 33.33 % and 53.33 % compared to 25 degrees C and 35 degrees C, respectively. Conversely, a rise in cooling water temperature enhanced the temperature uniformity and reduced thermal resistance of CBCPVC. At 35 degrees C and a heat load of 120 W, GBCPVC achieved a minimum thermal resistance of 0.034 K/W and a maximum temperature difference of 1.46 degrees C. Additionally, an increased flow rate enhanced the maximum heat load of GBCPVC, and under high heat loads, it could also reduce the thermal resistance and improve temperature uniformity. This study provides new insights and solutions for the thermal management of phase-change cooling components in aerospace electronic devices.

Numerical simulation of wickless gravity-assisted two-phase cooling system used in heavy duty extrusion pelleting line

Prediction Models of Saturated Vapor Pressure, Saturated Density, Surface Tension, Viscosity and Thermal Conductivity of Electronic Fluoride Liquids in Two-Phase Liquid Immersion Cooling Systems: A Comprehensive Review

Development and Validation of Helical-Coil-in-fluted-tube Gas Cooler for CO2 Heat Pump Water Heaters

Numerical Study on the Working Performance of a G-M Cryocooler with a Mechanically Driven Displacer

The Flow Numerical Simulation and Optimization for Evaporative Cooler

Numerical Simulation of Gas-Solid Two-Phase Heat Transfer in a Kaolin Cyclone Cooling System

Theoretical and Experimental Studies for a Transcritical CO2 Heat Pump with Spirally Fluted Tube Gas Cooler

Numerical calculation of fluid viscosity in Hot Hydrostatic Extrusion of high density tungsten alloy

Numerical Analysis of the Flow Characteristics and Heat and Mass Transfer of Falling-Water Films in an Industrial-Scale Dip Tube of A Wscc in an Omb Gasifier

Study of Refrigerated Mechanism of Evaporative of Air-Water Annular Two-Phase Flow in A Small Vertical Tube

Numerical Investigation on Thermal Performance of Two-Phase Immersion Cooling Method for High-Power Electronics

Analysis on the Mechanism of Evolutionary Process of Counter-Rotating Vortex Pair in Film Cooling Based on Hybrid Thermal Lattice Boltzmann Method

Numerical Analysis of Two-phase Flow and Heat Transfer in External Cyclic Purification Hot-dip Galvanizing Bath

Experimental research and numerical simulation of the thermal performance of a tube-fin cold energy storage unit using water/modified expanded graphite as the phase change material

Numerical Simulation of Subcooled Flow Boiling and Application to the EAST Plasma Facing Components

Numerical and Experimental Investigations of Electronic Evaporative Cooling Performance with a Coiled Channel

Numerical Simulation Of Flow And Heat Transfer In Connection Of Gasifier To The Radiant Syngas Cooler

Numerical Investigation on Heat Transfer Characteristics of High-Pressure Syngas in the Membrane Helical-Coil Cooler of a 2,000 T/d Gasifier

Thermo-Flow Performances for the Main-Auxiliary Integrated Natural Draft Dry Cooling System

Enhancing Heat Transfer Performance of Aluminum-Based Vapor Chamber with a Novel Bionic Wick Structure Fabricated Using Additive Manufacturing

Numeric Al Simulation and Optimization of Cooling System for 2 M Accelerating Tube