Abstract:Publication date: 10 January 2022 Source: Solid State Phenomena Vol. 327 Author(s): Jiehua Li, Maria Pammer, Ernst Neunteufl, Peter Schumacher AZ80 alloy has been widely used to produce high performance Mg casting and wrought parts for high-end applications due to its high mechanical properties and deformation ability. However, at least two important issues still need to be solved in order to further improve its mechanical properties and deformation ability. Firstly, the grain size of α-Mg in AZ80 alloy is relatively large (more than 1000 μm) due to a lack of efficient grain refinement methodologies. Secondly, the size of the eutectic Mg17Al12 phase is also large and the distribution of the eutectic Mg17Al12 phase is continuous, which is very harmful for the mechanical properties, in particular to elongation. In this paper, these two important issues are investigated by adding Mg3N2 sub-micron particle into AZ80 alloy and thereby refining the α-Mg and the eutectic Mg17Al12 phase. Firstly, the Mg3N2 sub-micron particle was directly added into AZ80 alloy by using mechanically stirring in the semi-solid state, subsequently the melting temperature was increased above the liquidous temperature, and finally the melting was casted in the liquid state. It was found that the grain size of α-Mg can be refined from 883.8 μm to 169.9 μm. More importantly, the eutectic Mg17Al12 phase was also refined and the distribution became discontinuous. It should be noted that directly adding the Mg3N2 sub-micron particle into AZ80 alloy leads to a great loss of the Mg3N2 sub-micron particle due to the weak wetting behavior between the Mg3N2 sub-micron particle and Mg melt. The second methodology through mixing Mg3N2 sub-micron particles with AZ91 chips using a twin extruder was also used to prepare AZ91 master alloy with 3wt.% Mg3N2 sub-micron particle, which was subsequently added into AZ80 alloy in the liquid state. In this way, a significant grain refinement of α-Mg and a simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy was also achieved. The grain size of α-Mg can be refined from 883.8 μm to 325.9 μm. However, no significant grain refinement by using UST was observed. Instead, the grain size increases from 325.9 μm to 448.6 μm, indicating that the Mg3N2 sub-micron particle may lose its grain refinement potency due to possible aggregation and clustering. This paper provides an efficient and simple methodology for the grain refinement of α-Mg and the simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy.

Effect of Rotating Gas Bubble Stirring Process Parameters on Purifying Effectiveness and Mechanical Properties of Sand-Cast Mg–10Gd–3Y–0.5Zr Alloy

Study on Microstructure of Semi-Solid Magnesium Alloy Manufactured by Gas Bubbles Stirring

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Effects of Vacuum-Stirring Purification Process on Al-6Mg Alloy Melt

Influence of Processing Parameters on Microstructure of Casting Rolling Semi-Solid AZ91D Magnesium Alloy

Effect of stirring speed and temperature on the microstructure and mechanical properties of A356 alloy under vacuum

Formation of Non-Dendritic Microstructure of Semi-Solid Magnesium Alloy by Introducing Gas Bubbles

Effects of Melt Treatments and Electromagnetic Stirring on the Microstructures of AZ91D Alloy

Purification of aluminium-silicon alloy by electromagnetic directional solidification: Degassing and grain refinement

Influences of Melt Treatment on Grain Sizes and Morphologies of Az91d Alloy

Purification Technique of Regenerated Magnesium Alloy Melt

Characterization of microstructure and nanoscale phase in Mg-15Gd-1Zn (wt.%) alloy fabricated by rotating magnetic field casting

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Achieving refined microstructures and improved mechanical properties in a cup-shaped Mg-Gd-Y-Zr alloy casting by novel near-liquidus squeeze cast process

Effects of Ultrasonic Treatment on Grain Refinement and Gas Removal in Magnesium Alloys

Effect of Gd content on microstructure and dynamic mechanical properties of solution-treated Mg−xGd−3Y−0.5Zr alloy

Effect of the Mg3N2 Sub-Micron Particle on the Grain Refinement of AZ80 Alloy

Effect of Heating Process on Microstructure of AZ91D Magnesium Alloy During Partial Remelting

Effect of electromagnetic stirring on degassing and mechanical properties of M174 heat-resistant alloy