Abstract:Publication date: 10 January 2022 Source: Solid State Phenomena Vol. 327 Author(s): Jiehua Li, Maria Pammer, Ernst Neunteufl, Peter Schumacher AZ80 alloy has been widely used to produce high performance Mg casting and wrought parts for high-end applications due to its high mechanical properties and deformation ability. However, at least two important issues still need to be solved in order to further improve its mechanical properties and deformation ability. Firstly, the grain size of α-Mg in AZ80 alloy is relatively large (more than 1000 μm) due to a lack of efficient grain refinement methodologies. Secondly, the size of the eutectic Mg17Al12 phase is also large and the distribution of the eutectic Mg17Al12 phase is continuous, which is very harmful for the mechanical properties, in particular to elongation. In this paper, these two important issues are investigated by adding Mg3N2 sub-micron particle into AZ80 alloy and thereby refining the α-Mg and the eutectic Mg17Al12 phase. Firstly, the Mg3N2 sub-micron particle was directly added into AZ80 alloy by using mechanically stirring in the semi-solid state, subsequently the melting temperature was increased above the liquidous temperature, and finally the melting was casted in the liquid state. It was found that the grain size of α-Mg can be refined from 883.8 μm to 169.9 μm. More importantly, the eutectic Mg17Al12 phase was also refined and the distribution became discontinuous. It should be noted that directly adding the Mg3N2 sub-micron particle into AZ80 alloy leads to a great loss of the Mg3N2 sub-micron particle due to the weak wetting behavior between the Mg3N2 sub-micron particle and Mg melt. The second methodology through mixing Mg3N2 sub-micron particles with AZ91 chips using a twin extruder was also used to prepare AZ91 master alloy with 3wt.% Mg3N2 sub-micron particle, which was subsequently added into AZ80 alloy in the liquid state. In this way, a significant grain refinement of α-Mg and a simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy was also achieved. The grain size of α-Mg can be refined from 883.8 μm to 325.9 μm. However, no significant grain refinement by using UST was observed. Instead, the grain size increases from 325.9 μm to 448.6 μm, indicating that the Mg3N2 sub-micron particle may lose its grain refinement potency due to possible aggregation and clustering. This paper provides an efficient and simple methodology for the grain refinement of α-Mg and the simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy.

Influences of Melt Treatment on Grain Sizes and Morphologies of Az91d Alloy

Effects of Melt Treatments and Electromagnetic Stirring on the Microstructures of AZ91D Alloy

Influence of Carbon Powder and Electromagnetic Stirring on the Microstructure of AZ91D Alloy

Influence of Electromagnetic Stirring Processing on Microstructure and Properties of AZ91D Alloy

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Effects of Smelting and Crystallization Condition on Microstructure and Properties of AZ91D Alloy

Effect of Primary Microstructure on Re-Melting Behavior of AZ91D Magnesium Alloy

Al-CeO2-Mg refiner on grain refinement, cast fluidity and mechanical properties of AZ91 alloy

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Effect of Electromagnetic Stirring and Solution Treatment on Microstructure and Properties of AZ31 Magnesium Alloy

Effects of Heating Temperature on Partial Remelting Microstructure of AZ91D Magnesium Alloy

Effect of Heating Process on Microstructure of AZ91D Magnesium Alloy During Partial Remelting

Effect of Ingot Size of Magnesium Alloy AZ91D on Microstructure During Isothermal Heat Treatment

Influences of Preparation Conditions and Melt Treatment Procedures on Melt Treatment Performance of Al-5Ti-B and Al-10Sr Master Alloys

Enhanced grain refinement and mechanical properties of AZ91 alloy by a novel Al-5.1V-2.3B refiner containing VB 2 and VB particles

Effect of the Mg3N2 Sub-Micron Particle on the Grain Refinement of AZ80 Alloy

Effect of Al-Nb-Ti-B addition on microstructures, tensile mechanical and damping properties of AZ91 alloy

Effects of electromagnetic stirring and subsequent homogenization treatment on the microstructure and mechanical properties of Al70Zn10Mg10Cu5Si5 multi-component alloy

Influence of Processing Parameters on Microstructure of Casting Rolling Semi-Solid AZ91D Magnesium Alloy

Effects and Mechanism of Ca on Refinement of AZ91D Alloy

Study on the Applications of Structure Heredity of AZ91D Alloy