Abstract:A 3D CFD model is proposed to simulate the liquid flow characteristics in a RSSDR.Detailed liquid-liquid flow patterns in the RSSDR are analysed.The simulated flow patterns show good coincidence with published experimental data.Liquid holdup rate of the aqueous and organic phases in the RSSDR are obtained.The liquid velocity distribution in the RSSDR is presented.In this work, the CFD approach is employed to analyse the liquid hydrodynamic behaviour in the rotor-stator spinning disc reactor (RSSDR). The effect of rotational speed (N) and volume flow rate (Q) on the liquid-liquid flow pattern and its transition are investigated. It is found that there are two typical flow pattern (film flow and filament flow) observed in the RSSDR. Increasing N and decreasing Q turn the film flow into the filament flow. The flow pattern criterion for transition of filament flow to film flow is also obtained. The simulation data show a good agreement with our previous published experimental results. In addition, the influence of N and Q on liquid holdup rate (ε) and liquid velocity distribution in the RSSDR are also studied. The results show that ε keeps stable and then decreases with the increase of N, increases and then keeps consistent with increasing Q. While the mean liquid velocity increases as increasing N, Q, and radial radius (r). The mean radial velocity increases with increasing N, Q, and decreasing r. This work leads a deep understanding of the liquid flow characteristics in the RSSDR and its optimization design and scaling up.
What problem does this paper attempt to address?
The main problem that this paper attempts to solve is to study the liquid flow characteristics in the rotor - stator rotating disc reactor (RSSDR) through the computational fluid dynamics (CFD) method, especially the liquid - liquid flow patterns and their transformation rules. Specifically, the author focuses on the influence of the rotational speed ($N$) and the volumetric flow rate ($Q$) on the liquid - liquid flow patterns, and how these parameters affect the liquid holdup ($\varepsilon$) and the liquid velocity distribution.
### Main Problem Analysis
1. **Liquid - Liquid Flow Patterns and Their Transformation**
- The author observes two typical liquid - liquid flow patterns: film flow and filament flow. As the rotational speed increases and the volumetric flow rate decreases, the film flow will transform into the filament flow.
- The research also determines the critical conditions for the transformation from filament flow to film flow, and it is found that the simulation results are in good agreement with the previously published experimental results.
2. **Liquid Holdup ($\varepsilon$)**
- The research shows that the liquid holdup remains stable at low rotational speeds, while it will decrease at high rotational speeds. In addition, as the volumetric flow rate increases, the liquid holdup first increases and then tends to be stable.
- The holdup of the aqueous phase is less than that of the organic phase, mainly because the density of the aqueous phase is larger, resulting in a faster flow speed under the action of centrifugal force, thus reducing the residence time.
3. **Liquid Velocity Distribution**
- The rotational speed has a significant influence on the average liquid velocity. As the rotational speed and the radial radius increase, the average liquid velocity also increases, but it slightly decreases at the outer edge of the rotor - stator cavity, which may be due to the disturbance caused by air inhalation.
- The average radial velocity increases as the rotational speed increases, and it first increases and then decreases as the radial radius goes from the center to the edge.
### Formula Representation
- **Continuity Equation**
\[
\frac{\partial (\alpha_q \rho_q)}{\partial t}+\nabla\cdot(\alpha_q \rho_q \mathbf{u}_q) = 0
\]
where $\alpha_q$ is the volume fraction of the $q$ - th phase, $\rho_q$ is the density of the $q$ - th phase, and $\mathbf{u}_q$ is the velocity of the $q$ - th phase.
- **Momentum Equation**
\[
\frac{\partial (\rho \mathbf{u})}{\partial t}+\nabla\cdot(\rho \mathbf{u}\mathbf{u})=-\nabla p+\nabla\cdot\left[\mu\left(\nabla \mathbf{u}+(\nabla \mathbf{u})^T\right)\right]+\rho \mathbf{g}+\mathbf{F}_V
\]
where $\rho$ is the average density of the mixed phase, $\mu$ is the average viscosity of the mixed phase, $\mathbf{g}$ is the gravitational acceleration, and $\mathbf{F}_V$ is the body force.
- **Surface Tension Force**
\[
\mathbf{F}_V=\sigma k \mathbf{n}
\]
where $\sigma$ is the surface tension coefficient, $k$ is the interface curvature, and $\mathbf{n}$ is the interface normal vector.
Through these studies, the author hopes to gain an in - depth understanding of the liquid flow characteristics in RSSDR, thereby providing a theoretical basis for optimal design and scale - up.