Abstract:With the development of electric vehicles (EVs) and hybrid electric vehicles (HEVs), the demand for lithium ion power batteries with high energy density and long cycle life has continuously increased in the recent years. According to the "Made in China 2025" plan, the energy densities of lithium ion batteries need to reach 300 Wh.kg(-1) in 2020. Due to their high discharge capacities and work voltages, Ni-rich layered materials have attracted considerable attention from the science and industry fields as one of the most promising cathodes to achieve high energy density. According to previous reports, the discharge capacities of Ni-rich cathodes were positively correlated to their Ni content. However, the increased Ni content can aggravate the side reactions between the cathode and electrolyte, induce O loss, and trigger structural transformation from the surface to bulk. In this study, ZrO2 was coated on LiNi0.8Co0.1Mn0.1O2 with a simple wet chemical method to improve its cycle performance. The scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) demonstrated that Zr was only detected in the ZrO2-coated samples and was mainly distributed at the surface of the secondary particles of the LiNi0.8Co0.1Mn0.1O2 cathodes. The X-ray diffraction (XRD) indicated that Zr4+ in ZrO2 migrated into the layered surface structure of LiNi0.8Co0.1Mn0.1O2 based on the shift of the (003) peak to a lower angle, which was considered as a lattice expansion along the c axis. Under the cut-off voltage of 4.3 and 4.5 V, the capacity retentions of the LiNi0.8Co0.1Mn0.1O2 cathodes improved from 84.89 to 97.61% and 75.60 to 81.37%, respectively, after 100 cycles at 1C. This was mainly attributed to the doped Zr4+ in surface structure as opposed to the ZrO2 coating. The X-ray photoelectron spectroscopy (XPS) indicated that the Ni3+ at the surface of LiNi0.8Co0.1Mn0.1O2 was reduced to Ni2+ after the Zr4+ surface doping due to charge balance. Rietveld refinement also indicated that the Li+/Ni2+ cation disordering improved after the Zr4+ in ZrO2 doped into NCM surface structure. The raised cation disordering may be triggered by the increased content of Ni2+ and their migration into Li layers due to the similar ion radius of Li+ (0.076 nm) and Ni2+ (0.069 nm). A structure-reconstructed layer at the surface of LiNi0.8Co0.1Mn0.1O2 was formed after the Zr4+ doping, which had been confirmed by transmission electron microscope (TEM). It was determined that this structure-reconstructed layer can hinder the side reactions at the interface and stabilize the bulk structure during cycles; thus, the cycle stability of LiNi0.8Co0.1Mn0.1O2 material was improved.

Enhanced low voltage cycling stability of LiMn2O4 cathode by ZnO coating for lithium ion batteries

Zr-doping Stabilizes Spinel LiMn 2 O 4 As a Low Cost Long Cycle Life Cathode for Lithium Ion Batteries

Microstructure boosting the cycling stability of LiNi0.6Co0.2Mn0.2O2 cathode through Zr-based dual modification

Inverse Spinel-Structured Mg2MnO4 Coating to Enable Superior Thermal Stability of LiNi0.83Co0.12Mn0.05O2 Cathodes for Lithium-Ion Batteries

Investigation the Electrochemical Performance of Li1.2Ni0.2Mn0.6O2 Cathode Material with ZnAl2O4 Coating for Lithium Ion Batteries

The Surface Al2o3 Coating and Bulk Zr Doping Drastically Improve the Voltage Fade and Cycling Stability of Li(Ni0.8mn0.1co0.1)O2 Cathode Materials

Improving the Stability Properties of 5 V Lithium Nickel Manganese Oxide Spinel by Surface Coating with Cobalt Aluminum Oxides for Lithium Ion Batteries

Enhanced Cycling Stability of LiMn2O4 by Surface Modification with Melting Impregnation Method

Surface modification by ZnO coating for improving the elevated temperature performance of LiMn2O4

Enhanced high-temperature cycling stability of LiNi1/3Co1/3Mn1/3O2-coated LiMn2O4 as cathode material for lithium ion batteries

Towards high-performance cathode materials for lithium-ion batteries: Al 2 O 3 -coated LiNi 0.8 Co 0.15 Zn 0.05 O 2

Direct Synthesis of Al2O3-modified Li(Ni0.5Co0.2Mn0.3)O2 Cathode Materials for Lithium Ion Batteries

Dual-Element-Modified Single-Crystal LiNi0.6Co0.2Mn0.2O2 As a Highly Stable Cathode for Lithium-Ion Batteries.

Enhanced High-Rate and Long-Cycle Performance of Mg2+-Al3+ Co-Doped Spinel LiMn2O4 Cathode Materials for Li-ion Batteries

Improving the cycling and air-storage stability of LiNi<sub>0.8</sub>Co<sub>0.1</sub>Mn<sub>0.1</sub>O<sub>2</sub> through integrated surface/interface/doping engineering

Strengthening Reversibility at High Rate of Spinel LiMn2O4 by Aluminum and Copper Co-doping for Lithium Ion Battery

Enhanced electrochemical performances of 5 v spinel LiMn 1.58Ni0.42O4 cathode materials by coating with LiAlO2

Effects of ZrO2 Coating on Ni-rich LiNi0.8Co0.1Mn0.1O2 Cathodes with Enhanced Cycle Stabilities

Achieving Superior High-Rate Cyclability of LiNi0.5Mn1.5O4 Cathode Material Via Constructing Stable CuO Modification Interface

Enhanced Electrochemical Properties of LiNi0.8Co0.1Mn0.1O2 at Elevated Temperature by Simultaneous Structure and Interface Regulating

Enhanced High-Potential and Elevated-Temperature Cycling Stability of Limn2o4 Cathode by Tio2 Modification for Li-Ion Battery