Abstract:Hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) require high power energy sources which are inexpensive and safe. Among various battery materials, 5V LiMn1.5Ni0.5O4 spinel materials are especially of interests for these vehicle applications because of their high operating voltage of ~4.7V and because manganese is inexpensive and less toxic than Ni and Co. However, the cycle life of these cathodes is inadequate and elevated temperature cycling cause rapid loss of capacity of the LiMn1.5Ni0.5O4 cells. This capacity degradation can be attributed to dissolution of Mn and Ni elements, solid electrolyte interphase (SEI) formation and electrolyte decomposition with high-voltage cycling [1]. Metal oxide coatings, which are usually synthesized by solution-based coating techniques, have improved capacity retention of the LiMn1.5Ni0.5O4 cells at the elevated temperatures and have been usually synthesized by solution-based coating techniques [2,3]. Recently, we have successfully coated nanometer thick amorphous lithium phosphorus oxyntirde (Lipon) electrolytes on the surfaces of LiMn1.5Ni0.5O4 and LiCoO2 particles by a RFmagnetron sputtering technique [4,5]. Uniform subnanometer thick Lipon improved the cycling behaviors of LiMn1.5Ni0.5O4 cells dramatically, but did not impede the Mn dissolution. Although a thicker Lipon layers of a few nanometers were effective in preventing the Mn dissolution, the Lipon layers greatly reduced the specific capacity because Lipon has a very low electronic conductivity of ~10 -14 S/cm. For comparison, nanometerthick protective films of electronic/ionic mixed conductor are being evaluated. Half-cell performances of cathodes fabricated with LiMn1.5Ni0.5O4 particles coated with mixed conductor will be reported for cycling at room and

Enhanced Cycling Stability of LiMn2O4 by Surface Modification with Melting Impregnation Method

Surface Modification and Electrochemical Properties of Li-Rich Layered Cathode Materials for Lithium-Ion Batteries

Electrochemical Performance of Surface-Modified LiMn2O4 Prepared by a Melting Impregnation Method

Enhanced low voltage cycling stability of LiMn2O4 cathode by ZnO coating for lithium ion batteries

Enhanced Cycle Stability of Spinel LiMn2O4 by a Melting Impregnation Method

Enhanced High-Potential and Elevated-Temperature Cycling Stability of Limn2o4 Cathode by Tio2 Modification for Li-Ion Battery

Cycling Stability of 5V LiMn1.5Ni0.5O4 Spinel Particles Coated with a Thin Film Mixed Conductor

Improved Li-ion Diffusion and Stability of a LiNi0.5Mn1.5O4 Cathode Through in Situ Co-Doping with Dual-Metal Cations and Incorporation of a Superionic Conductor

Enhanced cycling stability of Li[Li0.2Mn0.54Ni 0.13Co0.13]O2 by surface modification of MgO with melting impregnation method

Preparation, Characteristics and Electrochemical Properties of Surface-Modified Limn2o4 by Doped Lini0.05mn1.95o4

Surface Modification and Characterization of Spinel LiMn2O4 Coated with MgO

Surface Modification Mechanism of Spinel Structure LiM_xMn_(2-x)O_4 As Cathode Materials for Lithium Ion Batteries

Enhanced electrochemical performances of 5 v spinel LiMn 1.58Ni0.42O4 cathode materials by coating with LiAlO2

Effectively Suppressing Dissolution of Manganese from LiMn2O4 Spinel Via a Novel Nanoscale Surface-Doping Approach

Structure and Electrochemical Performance of Modificated LiMn<sub>2</sub>O<sub>4</sub> by S-Co Codoping and Nano SiO<sub>2</sub> Surface Coating

Enhanced high-temperature cycling stability of LiNi1/3Co1/3Mn1/3O2-coated LiMn2O4 as cathode material for lithium ion batteries

Structure and Electrochemical Performance of Modificated LiMn2O4 by S-Co Codoping and Nano SiO2 Surface Coating

Nanoscale Manipulation of Spinel Lithium Nickel Manganese Oxide Surface by Multisite Ti Occupation As High‐Performance Cathode

Surface Magnesium Substitution at Spinel Lithium Manganate 8a Tetrahedral Sites for Suppressed Manganese Dissolution and Enhanced Cycle Stability

Surface Modification of High Voltage Spinel LiNi 0.5 Mn 1.5 O 4 Cathode Material Manufactured via Co-precipitation

Improving the Electrochemical Performance of Li-rich Li1.2Ni0.2Mn0.6O2 by Using Ni-Mn Oxide Surface Modification