Abstract:Hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) require high power energy sources which are inexpensive and safe. Among various battery materials, 5V LiMn1.5Ni0.5O4 spinel materials are especially of interests for these vehicle applications because of their high operating voltage of ~4.7V and because manganese is inexpensive and less toxic than Ni and Co. However, the cycle life of these cathodes is inadequate and elevated temperature cycling cause rapid loss of capacity of the LiMn1.5Ni0.5O4 cells. This capacity degradation can be attributed to dissolution of Mn and Ni elements, solid electrolyte interphase (SEI) formation and electrolyte decomposition with high-voltage cycling [1]. Metal oxide coatings, which are usually synthesized by solution-based coating techniques, have improved capacity retention of the LiMn1.5Ni0.5O4 cells at the elevated temperatures and have been usually synthesized by solution-based coating techniques [2,3]. Recently, we have successfully coated nanometer thick amorphous lithium phosphorus oxyntirde (Lipon) electrolytes on the surfaces of LiMn1.5Ni0.5O4 and LiCoO2 particles by a RFmagnetron sputtering technique [4,5]. Uniform subnanometer thick Lipon improved the cycling behaviors of LiMn1.5Ni0.5O4 cells dramatically, but did not impede the Mn dissolution. Although a thicker Lipon layers of a few nanometers were effective in preventing the Mn dissolution, the Lipon layers greatly reduced the specific capacity because Lipon has a very low electronic conductivity of ~10 -14 S/cm. For comparison, nanometerthick protective films of electronic/ionic mixed conductor are being evaluated. Half-cell performances of cathodes fabricated with LiMn1.5Ni0.5O4 particles coated with mixed conductor will be reported for cycling at room and

Enhanced Cycle Stability of Spinel LiMn2O4 by a Melting Impregnation Method

Cycling Stability of 5V LiMn1.5Ni0.5O4 Spinel Particles Coated with a Thin Film Mixed Conductor

Enhanced Cycling Stability of LiMn2O4 by Surface Modification with Melting Impregnation Method

Enhanced low voltage cycling stability of LiMn2O4 cathode by ZnO coating for lithium ion batteries

Enhanced cycling stability of Li[Li0.2Mn0.54Ni 0.13Co0.13]O2 by surface modification of MgO with melting impregnation method

Enhanced Cycling Performance of Spinel LiNi0.5Mn1.5O4 Cathodes through Mg-Mn Hetero-Valent Doping via Microwave Sol-Gel Method

Boosting the cycling performance of spinel LiMn2O4 by in situ MnBO3 coating

Structure and Electrochemical Performance of Modificated LiMn<sub>2</sub>O<sub>4</sub> by S-Co Codoping and Nano SiO<sub>2</sub> Surface Coating

Cycling Stability of Spinel LiMn2O4 with Different Particle Sizes in Aqueous Electrolyte

Research on Electrochemical Properties of Metal Oxides Coated LiNi_(0.4)Co_(0.2)Mn_(0.4)O_2 by Melting Impregnation

Structure and Electrochemical Performance of Modificated LiMn2O4 by S-Co Codoping and Nano SiO2 Surface Coating

Enhanced High-Potential and Elevated-Temperature Cycling Stability of Limn2o4 Cathode by Tio2 Modification for Li-Ion Battery

Correlating Cycle Performance Improvement and Structural Alleviation in LiMn2-xMxO4 Spinel Cathode Materials: A Systematic Study on the Effects of Metal-Ion Doping

Inverse Spinel-Structured Mg2MnO4 Coating to Enable Superior Thermal Stability of LiNi0.83Co0.12Mn0.05O2 Cathodes for Lithium-Ion Batteries

Electrochemical Performance of Surface-Modified LiMn2O4 Prepared by a Melting Impregnation Method

Enhanced Electrochemical Performances of 5 V Spinel LiMn1.58Ni0.42O4 Cathode Materials by Coating with LiAlO2

Improved Cycling Performance of Oxygen-Stoichiometric Spinel Li1+xAlyMn2−x−yO4+δ at Elevated Temperature

Enhanced high-temperature cycling stability of LiNi1/3Co1/3Mn1/3O2-coated LiMn2O4 as cathode material for lithium ion batteries

Li2ZrO3 Coated LiFe0.4Mn0.6PO4/C with Enhanced Cycling Performance at Elevated Temperature for Lithium-Ion Batteries

Strengthening Reversibility at High Rate of Spinel LiMn2O4 by Aluminum and Copper Co-doping for Lithium Ion Battery

Doping Mg2+ to Improve the Li+ Diffusion Rate and Electrochemical Performance of Spinel LiMn2O4