Abstract:Nitrogen-rich ultra-thin (1-2 nm thick) layers in diamond produced by high-temperature nitrogen ion (N2+) implantation at low N2+ energies studied by in situ x-ray photoelectron spectroscopy are reported. Nitrogen bonding at the subsurface region and its thermal stability, as well as structural defects in polycrystalline diamond (PCD) implanted with 200, 500, and 800 eV N2+ at room temperature (RT) and 600 °C at an ion dose of 4.5 × 1014 ions/cm2, are investigated. Implantation at RT leads to nitrogen bonding at interstitial and substitutional sites in the diamond lattice, which is associated with the C-N/C=N bond, lower intensity of the C≡N (nitrile-like) component associated with nitrogen bonding with carbon defects, and quaternary nitrogen. The relative composition of these chemical states varies with implantation energy, temperature, and post-implantation annealing temperature. Upon annealing the RT implanted layers above 500-600 °C, the interstitial nitrogen converts to substitutional nitrogen. This process competes with nitrogen desorption. The thermal stability of nitrogen increases with implantation energy. Implantation at 600 °C at 800 eV resulted in a significantly lower concentration of nitrile-like bonds and a lower density of structural defects compared to RT implantation at the same energy. These effects are associated with dynamic annealing, which becomes more significant at higher implantation energies. Upon high-temperature implantation, nitrogen mostly populates directly substitutional sites. Nitrogen implantation at low energy and high temperature may be a viable way to nitride diamond surfaces with reduced density of defects where nitrogen is selectively bonded to substitutional sites. Finally, a comparison between nitrogen implantation into PCD and Diamond (100) [Di(100)] surfaces is presented.

Structure and Wear Behavior of Nitrogen-Implanted Aluminum Alloys*

The effect of N+-implanted aluminum substrate on the mechanical properties of TiN films

Fretting wear behavior of nitrogen implanted Zircaloy-4 alloy

Microstructural evolution and vibration fatigue properties of 7075-T651 aluminum alloy treated by nitrogen ion implantation

Influence of Nitrogen Implantation on Adhesion Strength of TiAlN Film on Γ-Tial Alloy

Nitrogen Ion Implantation on the Mechanical Properties of Aisi 420 Martensitic Stainless Steel

Aluminium nitride layers prepared by nitrogen arc discharge on Al-Si alloy substrate

Effects of Nitrogen Ion Implantation and Implantation Energy on Surface Properties and Adhesion Strength of TiN Films Deposited on Aluminum by Magnetron Sputtering

Microstructure and wear behavior of inductive nitriding layer in Ti–25Nb–3Zr–2Sn–3Mo alloys

Structure and Wear Properties of NiTi Modified by Nitrogen Plasma Immersion Ion Implantation

Modification mechanism of Ti-6Al-4V alloy with pre-coated Ti-Cu-Al multilayer film treated by ion nitriding: Experiments and first-principles calculations

Investigation on the Microstructure and High-Temperature Properties of AlN Coating Through Oxygen Addition

Effects of nitrogen content on microstructures and mechanical properties of (AlCrTiZrHf)N high-entropy alloy nitride films

Improvement of Impact Wear Performance of Ti6Al4V Alloy by Nitrogen Ion Implantation and Nitriding

Improvement of nitrogen ion implantation on the wear and corrosion resistance of bearing steel in NaCl solution

Dynamic annealing assisted near-surface structural and bond stabilization in high-temperature low-energy N2+ implanted diamond

Improving wear resistance of Zr-2.5Nb alloy by formation of microtextured nitride layer produced via laser surface texturing/plasma nitriding technology

Mechanical behavior, tribological properties, and thermal stability of (AlCrNbSiTiVZr)N high entropy alloy nitride coatings and their application to Inconel 718 milling

Structural and Mechanical Properties of Radiofrequency Ar-N2 Plasma Nitrided Aluminium

MODIFICATION OF TRIBOLOGICAL CHARACTERISTICS OF METALS AFTER NITROGEN IMPLANTATION

High Current Ni- and Fe-ion Implantation into an Al Surface to Modify the Mechanical Properties