Abstract:Medium-entropy Zr–Nb–Ti (ZNT) alloys are being extensively investigated as load-bearing implant materials because of their exceptional biocompatibility and corrosion resistance, and low magnetic susceptibility. Nevertheless, enhancing their yield strength while simultaneously decreasing their elastic modulus presents a formidable obstacle, significantly constraining their broader utilization as metallic biomaterials. In this study, three medium-entropy ZNT alloys, i.e., Zr 45 Nb 45 Ti 10 , Zr 42.5 Nb 42.5 Ti 15 , and Zr 40 Nb 40 Ti 20 (denoted ZNT 10 , ZNT 15 , and ZNT 20 , respectively), were designed based on the miscibility gap in the ZNT phase diagram and prepared by annealing of cold-rolled ingots. Their microstructures, mechanical properties, wear resistance, corrosion resistance, magnetic susceptibility, and biocompatibility were systematically studied. Spinodal decomposition occurred in the cold-rolled ZNT 10 and ZNTi 15 after annealing at 650°C for 2 h and resulted in nanoscale Zr-rich β 1 and (Nb, Ti)-rich β 2 phases, which significantly improved their yield strength and reduced their elastic modulus. The wear resistance of the alloys decreased with an increase in Ti content. Dense ZrO 2 , Nb 2 O 5 , and TiO 2 oxide layers were formed during the polarization process in Hanks' solution, which enhanced the corrosion resistance of the alloys. These ZNT alloys exhibited significantly lower magnetic susceptibility than medical Ti alloys. The ZNT alloys showed a cell viability of more than 94 % toward MG-63 cells after culturing for 3 d. Overall, the spinodal ZNT 15 showed the best combination of mechanical properties, wear resistance, corrosion resistance, low magnetic susceptibility, and sufficient biocompatibility among the three alloys. Statement of Significance This work reports on medium-entropy Zr–Nb–Ti (ZNT) alloys with heterostructure. Spinodal decomposition significantly improved their mechanical strength and reduced the elastic modulus of the alloys. The wear resistance of the ZNT alloys decreased with an increase in Ti content. Dense ZrO 2 , Nb 2 O 5 , and TiO 2 oxide layers were formed during the polarization process in Hanks' solution, which enhanced the corrosion resistance of the alloys. The ZNT alloys exhibited significantly lower magnetic susceptibility than medical Ti alloys. The ZNT alloys showed a cell viability of more than 94% toward MG-63 cells after culturing for 3 d. The results demonstrate that spinodal ZNT alloys have enormous potential as bone-implant materials due to their outstanding overall mechanical properties, high corrosion resistance, wear resistance, low magnetic susceptibility, and sufficient biocompatibility.

Improving wear resistance of Zr-2.5Nb alloy by formation of microtextured nitride layer produced via laser surface texturing/plasma nitriding technology

Enhancing wear resistance and biocompatibility of medical ZrNb alloy used for artificial joint via femtosecond laser surface processing combined with thermal oxidation

The characteristic and osteogenic effect of a nanoporous coating of zirconia implant

Microstructure and wear behavior of inductive nitriding layer in Ti–25Nb–3Zr–2Sn–3Mo alloys

Microstructure evolution and vacuum tribological properties of surface nitriding layer on a TiZrAlV alloy fabricated by laser nitriding

Study of TiCuN/ZrN multilayer coatings with adjustable combination properties deposited on TiCu alloy

Improved mechanical and biological properties of Ti-13Nb-13Zr alloy treated by surface ultrasonic rolling and copper infiltration

Deposition and Characterization of a ZrN/Zr/a-C Multilayer: Implication on Bio-Tribological and Corrosion Behaviors

Microstructure, corrosion behavior and cytotoxicity of Zr–Nb alloys for biomedical application

New β-type Ti-Zr-V-Nb alloys used for laser-based direct energy deposition: Design, microstructure, and properties

Improving the Bio-Tribological Properties of Ti6Al4V Alloy via Combined Treatment of Femtosecond Laser Nitriding and Texturing

Insights into the surface and biocompatibility aspects of laser shock peened Ti-22Nb alloy for orthopedic implant applications

Improved tribological behavior of plasma-nitrided AlCrTiV and AlCrTiVSi high-entropy alloy films

Improved Tribological Performance of Nitride-Reinforced Biocompatible Titanium–Niobium–Zirconium–Tantalum (TNZT) Alloys for Advanced Orthopedic Applications

Deposition, microstructure and nanoindentation of multilayer Zr nitride and carbonitride nanostructured coatings

Tuning microstructure and mechanical and wear resistance of ZrNbTiMo refractory high-entropy alloy films via sputtering power

Structure-Dependent Tribological Investigation of Hierarchically ZrN-Coated Low-Carbon Steel for Automotive Applications

Wear characteristics of Ti–Nb–Ta–Zr and Ti–6Al–4V alloys for biomedical applications

Medium-entropy Zr–Nb–Ti alloys with low magnetic susceptibility, high yield strength, and low elastic modulus through spinodal decomposition for bone-implant applications

The Surface Modification of ZrO2 Film by Zr/Nb Ion Implantation and First-Principles Calculation

Evaluation of microstructure, mechanical properties and osseointegration capacity of laser cladding β-type TiNbZr coatings