Abstract:The study of liquid metal oxidation is of particular importance since some liquid metals are highly reactive with oxygen even under ultrahigh vacuum. The investigation of the oxidation behavior of liquid aluminum is strongly demanded due to its wide applications but relatively low melting point. However, it is still ambiguous about the products at the initial oxidation stage of liquid aluminum through the researches done in the past several decades. In order to investigate the initial oxidation products together with the oxidation mechanism of liquid aluminum, in-situ oxidation of nano aluminum powder was carried out at 720 degrees C in the environmental TEM (E-TEM). Prior to the oxidation, the nano aluminum powder was visualized and analyzed by E-TEM and DTA respectively. The results show that there is an amorphous Al2O3 film of 5-6 nm thick on the surface of the aluminum powder, which transforms to gamma-Al2O3 at a temperature range of 350-550 degrees C. By melting the nano powder to liquid followed by cooling under a total pressure of 10(-4) Pa in E-TEM, oxide-free solid aluminum is obtained. Re-melting of the solid aluminum at 720 degrees C yields oxide-free liquid aluminum. After oxidation of the oxide-free liquid aluminum under an oxygen partial pressure of 10(-2) Pa in E-TEM, alpha-Al2O3 nano wires appear on the liquid aluminum surface, demonstrating that the initial oxidation product of liquid aluminum is alpha-Al2O3. Moreover, the oxidation of liquid aluminum prepared from oxide-free bulk aluminum at 720 degrees C under an oxygen partial pressure of 10(-2) Pa was also studied. The XRD analysis of the products confirms that the oxide is constituted of single alpha-Al2O3. Additionally, this particular oxidation result of liquid aluminum is attributed to its liquid structure and vapor oxidation process.

ESEM Observation of the Process of Hydrogen Generation Around the Micro-Droplets Forming on AZ91 Magnesium Alloy

In Situ Observation of Formation and Spreading of Micro-Droplets on Magnesium and Its Alloy under Cyclic Wet–dry Conditions

In Situ Observation of Initial Corrosion of AZ91 Alloy with Residual Stress in Wet-Dry Conditions Using Environmental Scanning Electron Microscope

In Situ Observation of Pit Initiation of Passivated AZ91 Magnesium Alloy

States and Transport of Hydrogen in the Corrosion Process of an Az91 Magnesium Alloy in Aqueous Solution

Formation of Hydrogen Blister on AZ91 Magnesium Alloy During Cathodic Charging

Research Status of Hydrogen Evolution during Magnesium Alloy′s Corrosion Process

In Situ Observation of Electrolytic H2 Evolution Adjacent to Gold Cathodes.

Effects of Dust and Salt Particles on the Formation and Spreading of Micro-Droplets on AZ91 Magnesium Alloy

Quantitative Monitoring of the Environmental Hydrogen Embrittlement of Al-Zn-Mg-Based Aluminum Alloys via Dynamic Hydrogen Detection and Digital Image Correlation

Transmission Electron Microscopy Study of Aqueous Film Formation and Evolution on Magnesium Alloys

Revealing the Reaction Pathway of Anodic Hydrogen Evolution at Magnesium Surfaces in Aqueous Electrolytes

AC Impedance Spectroscopy Study of the Corrosion Behavior of an AZ91 Magnesium Alloy in 0.1 M Sodium Sulfate Solution

The Corrosion Behavior of AZ91D Magnesium Alloy in Simulated Haze Aqueous Solution

Observation on the Oxidation of Liquid Al by Environmental Transmission Electron Microscope

Study on the Anodic Film Formation Process of AZ91D Magnesium Alloy

A Mg Alloy with No Hydrogen Evolution During Dissolution

Effect of Hydrogen on Corrosion and Stress Corrosion Cracking of AZ91 Alloy in Aqueous Solutions

In Situ Study of the Initiation of Hydrogen Bubbles at the Aluminium Metal/oxide Interface.

Materials to Generate Hydrogen Continuously by Aluminium and Water Reaction at Room Temperature and Normal Pressure

Direct Observation of Atomic-Scale Origins of Local Dissolution in Al-Cu-Mg Alloys