Abstract:Injection molding is widely used for the mass production of plastic components. However, an appropriate choice of the process parameters is essential to ensure the precision and uniformity of the molded parts. The flow length-to-wall thickness (L/t) ratio for most molded components lies in the range of 100∼200. For higher values of the L/t ratio, the flow resistance increases dramatically at the end of the molded part and the injection pressure propagates less easily through the mold cavity. Consequently, the geometric dimensions of the molded parts in the near-gate region are frequently different from those in the far-from-gate region as well as resulting in lower uniformity. In practice, the variation in the geometric dimensions is significantly dependent on the filling-to-holding (V/P) switchover point, injection speed, and holding condition. Accordingly, the present study commences by proposing a simple least-squares regression-based approach for determining the appropriate V/P switchover point based on the quality requirement for the geometric dimensions of the molded component. In addition, a multi-stage holding condition is used to improve the geometric uniformity of the molded component by minimizing the residual pressure difference between the near-gate and far-from-gate regions of the mold at the end of the packing stage. Finally, a deceleration strategy is considered for the injection screw at the end of the filling stage to further reduce the quality variation. The experimental results show that for molded components with a large L/t ratio, the V/P switchover point should be determined based on the quality requirement for the part in the far-from-gate region in order to avoid insufficient quality compensation in the early holding stage. Furthermore, compared with the single-stage holding condition, the multi-stage holding condition reduces the residual pressure difference between the near-gate and far-from-gate regions of the cavity by around 74.5% (from 48.7 to 12.5 MPa). As a result, the difference in width between the near-gate region of the molded component and the far-from-gate region is reduced by about 66.7% (0.09 to 0.03 mm), while the difference in thickness is reduced by approximately 32.1% (0.028 to 0.019 mm). The deceleration strategy for the injection screw has no noticeable effect on the quality uniformity of the molded part provided that the V/P switchover point and multi-stage holding pressure are appropriately designed.

Study of screw configuration vs UPVC plastic injection moulding mixing influence

Finite Element Analysis and Optimal Researchon Plasticizing Capacity of Screws

The Study of the effect of material mixing on pin injection screw

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

Simulation and Experimental Analysis on Non-circular Cross-section Parts Residual Wall Thickness of Water-assisted Injection Molding

Numerical simulation of filling flow of polymer melt in injection molding

Study of Dynamic Flow and Mixing Performances of Tri-Screw Extruders with Finite Element Method

Numerical Study of Heat Transfer and Temperature in the Screw Groove for Molten Plastic

Study on Polymer Flow Profile in Micro Hot Embossing

Study on Simulation of Molten Polymer Flow in the Screw Groove

Mixing and Thermal Transport Behavior in a Pin or Non-Pin Extruder Equipped with a Field Synergy Elongation Screw

Effect of Dynamic Center Region on the Flow and Mixing Efficiency in a New Tri-Screw Extruder Using 3D Finite Element Modeling

Simulation of High-Viscosity Generalized Newtonian Fluid Flows in the Mixing Section of a Screw Extruder Using the Lattice Boltzmann Model

Study on Computer Simulation of Co-injection Molding

Research on the Application of Injection Molding Simulation Technology in Mold Design

Determination of process parameters based on cavity pressure characteristics to enhance quality uniformity in injection molding

Effects of Screw Clearance and Blend Ratio on the Flow and Mixing Characteristics of Tri-Screw Extruders in Cross Section with CFD

Investigation of 2D ultrasonic-assisted micro-injection molding

Effect of speed sinusoidal pulsating enhancement on the mixing property of plastic machinery

Analysis of the Dispersive and Distributive Mixing Effect of Screw Elements on the Co-Rotating Twin-Screw Extruder with Particle Tracking

Numerical Simulation and Experimental Validation of Mixing Performance of Kneading Discs in A Twin Screw Extruder