Abstract:Water-powered projectile-assisted injection molding (W-PAIM) is a novel injection molding technology that has been recently developed based on the ripe water-assisted injection molding (WAIM). Fiber orientation pattern and residual wall thickness (RWT) are two crucial factors determining the quality of W-PAIM parts composed of short fiber-reinforced thermoplastics (SFRTCs). However, limited work has been conducted on W-PAIM of SFRTC parts, which restricts its application process. In this work, an intensive investigation of W-PAIM parts composed of short fiber-reinforced polypropylene was conducted via a newly lab-developed W-PAIM platform. The results indicated that fibers were quite well oriented in the region extending from the core zone to the water channel, especially in the water channel zone, but randomly aligned in a small region near the mold wall. Nevertheless, fibers in the water channel zone of W-PAIM part were highly oriented, presenting an opposite alignment trend in fiber orientation compared to that in the water channel zone of the WAIM part as reported earlier. These disparities in fiber orientation between W-PAIM and WAIM parts were primarily attributed to the strong flow fields generated by projectile penetration. Additionally, the influence of three main processing parameters that significantly affected the projectile penetration on these two crucial factors was also investigated using the single-factor method. It was discovered that water injection delay time constituted the primary factor affecting the projectile penetration process, and reducing this time could greatly increase the relative thickness of the ordered area and the uniformity of RWT. More importantly, within the value range of the tested processing parameters, increased water pressure, elevated melt temperatures, and shorter water injection delay time could simultaneously improve fiber orientation and the uniformity of RWT in W-PAIM parts, which may improve the properties of W-PAIM parts and enlarge their application scope. This work provides a comprehensive guide for the fabrication of W-PAIM parts of SFRTCs.

Simulation and Experimental Analysis on Non-circular Cross-section Parts Residual Wall Thickness of Water-assisted Injection Molding

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

ANALYSIS OF LOAD CHARACTERISTICS AND CONTROL OF WATER HYDRAULIC SYSTEM FOR WAIM

Applications of Water-Assisted Injection Molding on Front Fork of Bicycle

Proportional Pressure Control Of Water Hydraulic System For Water-Assisted Injection Molding: Modeling And Simulation

Simulation and Experiment Research on the Proportional Pressure Control of Water-Assisted Injection Molding

Study of Residual Wall Thickness and Multiobjective Optimization for Process Parameters of Water-Assisted Injection Molding

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Experimental and numerical investigations on formation mechanisms of hollow structures in overflow water‐assisted injection‐molded parts of short‐glass‐fiber‐reinforced polypropylene

Numerical Simulation on the Penetration Behavior of the Projectile during the Water Injection Stage of Water-Projectile-Assisted Injection Molding Process

Experimental analysis of fluid‐assisted injection molding of pipe fittings with different angles by short‐shot method

Cavity Filling Analysis of Injection Molding Simulation:The Formation of Bubble and Weld Line

Research on the integral forming process of thin walled and thick mouth seamless gas cylinders

Water Analogue Experimental Study on the Filling Process of A Steam Turbine Housing Casting

Research on the Application of Injection Molding Simulation Technology in Mold Design

An integrated simulation method for analyzing mechanical properties of injection molded fiber‐reinforced polymers

Nondestructive Measurement of Layer Thickness in Water‐assisted Coinjection‐molded Product by Ultrasonic Technology

Warpage analysis and optimization of thin-walled injection molding parts based on numerical simulation and orthogonal experiment

Effects of Heat Input on Morphology of Thin‐Wall Components Fabricated by Wire and Arc Additive Manufacturing

The Investigation of Overflow Water-Powered Projectile-Assisted Injection Molded Short-Glass-Fiber-Reinforced Polypropylene

Numerical investigation and optimum design of complex thin-walled structures subject to internal pressure load