Abstract:High dielectric loss is a major drawback in CCTO-based electroceramics, and such high dielectric loss supports good microwave coupling for microwave synthesis of ceramics. Al substitution at Ti site and presence of moderate amount of secondary CuO intergranular melt-like phase can improve the dielectric properties of the ceramics. Therefore, microwave-assisted solid-state reaction was used to synthesize polycrystalline CaCu3Ti4−xAlxO12 (x = 0, 0.025, 0.05, 0.075, 0.1) ceramics. Lattice parameters and different amount of CuO phase were extracted from X-ray diffraction data via Rietveld refinement. Presence of grains with different morphology, and different kind of interfaces were confirmed through microstructure evolution. An approximate elemental analysis was revealed through selective area EDX. Variations in dielectric and impedance properties with frequency and temperature were investigated as an effect of Al3+ substitution at Ti4+ sites and appearance of secondary CuO phase. Maximum dielectric constant (εr) ~ 23,000 with ‘tan δ’ ~ 0.076 at 100 Hz has been observed for x = 0.05 ceramics at room temperature. Equivalent electrical circuits were proposed to understand the contributions arising from different electrically heterogeneous portions of CCTO-based ceramics. An elementary theoretical framework, based on different grains and interfaces (boundaries), has been proposed to understand the improved dielectric properties. Activation energies were calculated from imaginary part of impedance (Z″) and modulus (M″) functions and the values were in close agreement with activation energies associated to oxygen vacancies. In addition, defect chemistry has been discussed to understand the appearance of CuO phase as melt and the improvement of dielectric loss.

Preparation of CuO-TiO2 Composite Nanopowder and In-Situ Doping in Al2O3 Microwave Dielectric Ceramics

Low -temperature sintering of Al2O3 microwave dielectric ceramic doped with CuO-TiO2 gel

Sintering and dielectric properties of Al 2 O 3 ceramics doped by TiO 2 and CuO

Sintering and Dielectric Properties of Al2o3 Ceramics Doped by Tio2 and Cuo

Microstructure and Dielectric Properties of Novel MgTiO3-x Wt% MgAl2O4 Microwave Dielectric Composite Ceramics

Low-temperature sintering of Al2O3 ceramics doped with 4CuO-TiO2-2Nb2O5 composite oxide sintering aid

Effect of UV irradiation on the densification behavior, microstructure, and microwave dielectric properties of low temperature sintering Al2O3 ceramics

MnO2 on eliminating Al2TiO5 and promoting microwave dielectric properties of 0.90Al2O3–0.10TiO2 composite ceramics

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Effect of MnCO3 on Eliminating Al2TiO5 Phase and Dielectric Properties of 0.90Al2O3–0.10TiO2 Composite Ceramics

Effects Of Catio(3)On Microstructures And Properties Of (1-X) Znal2o4-Xmg(2) Tio4 (X=0.1) Microwave Dielectric Ceramics

Characterization and Microwave Dielectric Properties of TiO2-modified 0.65catio3–0.35sm0.9nd0.1alo3 Ceramics

Preparation of 0.5pbtio_3/0.5nife_2o_4 Ceramic Composites by Sol-gel Method

Preparation and Dielectric Properties of (ca0.61,nd0.26)tio3 Nanoparticles by a Sol–gel Method

Microwave Dielectric Properties of 0.9Al203-0.1Tio2 Ceramics Prepared by Aqueous Gelcasting

A comparative study of microstructure and electrical properties of (Al, Nb) co-doped TiO2 ceramics by different sintering methods

Microstructure and Microwave Dielectric Properties of Tio2-Doped Zn2sio4 Ceramics Synthesized Through the Sol-Gel Process

Modification of Low Temperature Sintered CMS Microwave Dielectric Ceramics Doped with Nanopowder

Effect of Al substitution and secondary CuO phase on dielectric response in microwave-processed CaCu3Ti4−xAlxO12 ceramics

Low-fired microwave dielectrics in ZnO-TiO 2 ceramics doped with CuO and B 2 O 3