Abstract:Based on the response surface methodology (RSM), Cu-Mn-Ce catalysts were prepared via the vacuum impregnation method. Also, Their performance in the oxidation of a tar model compound (Benzene, 5,000 ppm) was evaluated. Results show that the optimum condition is CuO-MnO content of 30% and CeO2 content of 4.4% at a calcination temperature of 620 °C for 4.1 h. In this condition, the confirmatory experiment indicates the average carbon conversion rate within half an hour (Xc-0.5h) and four hours (Xc-4h) are 99.5% and 97.1% at 300 °C, respectively, which is in good agreement with the model prediction. XRD, H2-TPR, SEM, and XPS were employed in catalyst characterization. CuO is the primary active metal in the catalysts, which is affected easily by the calcination temperature. A lower calcination temperature tends to cause a weak structure strength, but a higher temperature results in impairing the reducibility. The major roles of CeO2 are displayed in two aspects that CeO2 increases the dispersion of the active metal, enhances the catalyst stability, and increases the oxygen vacancies and improves the oxygen transfer ability. For Cu-Mn-Ce composite catalyst, the catalytic oxidization of benzene complies with the Mars-van Krevelen mechanism (MVK). The content of CuO-MnO determines the number of active sites on the catalyst, which promotes the reduction of catalyst. CeO2 plays an important role in enhancing the oxidization of the catalyst. Therefore, the ratio of CuO-MnO to CeO2 in the catalyst will cause a change of the control step of the redox reaction.

Catalytic Oxidation of Chlorobenzene over Mnox/Al2o3-Carbon Nanotubes Composites

Low temperature chlorobenzene catalytic oxidation over MnOx/CNTs with the assistance of ozone

Enhanced Performance of Binary WO3/N-doped Carbon Composites for the Catalytic Oxidation of Benzyl Alcohol under Mild Conditions

Low-temperature Catalytic Oxidation of Chlorobenzene over MnOX/TiO2–CNTs Nano-Composites Prepared by Wet Synthesis Methods

Catalytic Oxidation of Chlorobenzene over V2o5/Tio2-Carbon Nanotubes Composites

Catalytic Oxidation Of Chlorobenzene Over V2o5/Tio2-Cnts Nano Composites

In Situ Fabrication of Highly Active Γ-Mno2/smmno3 Catalyst for Deep Catalytic Oxidation of Gaseous Benzene, Ethylbenzene, Toluene, and O-Xylene.

Catalytic Decomposition of 1,2-Dichlorobenzene over V2O5/TiO2 Catalysts Blending with Typical Carbon Nanotubes

Catalytic Oxidation of 1,2-Dcbz over V2O5/TiO2-CNTs: Effect of CNT Diameter and Surface Functional Groups.

Preparation of MnOx/TiO2 composites and their properties for catalytic oxidation of chlorobenzene.

Catalytic Oxidation of Chlorobenzene over Ce-Mn-O<sub>x</sub>/TiO<sub>2</sub>: Performance Study of the Porous Structure

Ozone Promotion of Monochlorobenzene Catalytic Oxidation Over Carbon Nanotubes-Supported Copper Oxide at High Temperature

Catalytic oxidation of benzene over alumina-supported Cu-Mn-Ce mixed oxide catalysts

Enhanced catalytic activities of MnOx/Co3O4 nanocomposites prepared via MOFs-templated approach for chlorobenzene oxidation

Catalytic Degradation of 1,2-Chlorobenzene and Dioxins Coupled by Kinds of Methods

Mofs-derived CuCeOx Supported on H-zeolite Socony Mobile-5 for Catalytic Oxidation of 1,2-Dichlorobenzene

Ozone Assisted Oxidation of Gaseous PCDD/Fs over CNTs-containing Composite Catalysts at Low Temperature.

Catalytic Oxidation of Chlorobenzene over MnxCe1-xO2/HZSM-5 Catalysts: A Study with Practical Implications.

Pt and Mo Co-Decorated MnO2 Nanorods with Superior Resistance to H2O, Sintering, and HCl for Catalytic Oxidation of Chlorobenzene.

Pt and Mo Co-Decorated MnO 2 Nanorods with Superior Resistance to H 2 O, Sintering, and HCl for Catalytic Oxidation of Chlorobenzene

Efficient MnCeO x catalyst derived from MnCe-MOF for chlorobenzene oxidation: Effects of metal ratio, pyrolysis atmosphere and pyrolysis temperature