Abstract:Employment of high-capacity positive-electrode materials is one of the most effective ways to improve the energy density of Li-ion batteries. The electrochemical properties of Li transition-metal oxides, which make up the Li insertion materials in the positive electrode, depend on their crystal structures. In general, materials composed of LiMO2 (M: a transition metal) with a layered structure (i.e., a two-dimensional framework) exhibit a high capacity, but complete extraction of the Li ions in the framework results in destruction of the structure. LiM2O4 having a spinel structure (i.e., a three-dimensional framework) exhibits excellent toughness, but the number of Li ions in the structure is smaller than that in the layered structure, resulting in a lower reversible capacity. Li2M2O4 with a reduced spinel-framework structure can be expected to have the advantages of both layered and spinel structures: high capacity and robust structure. In this study, a cubic polymorph of LiNi1/2Mn1/2O2, which is thought to be a layered material, was prepared by low-temperature synthesis. The obtained LiNi1/2Mn1/2O2 was electrochemically active and showed a reversible capacity of > 100 mAh g−1 at an upper limit voltage of 4.2 V, which is almost the same as that of a two-dimensional material with a layered structure. To confirm the crystal structure of low-temperature LiNi1/2Mn1/2O2, the change in crystal structure during Li extraction was investigated by ex situ XRD measurements. The isotropic contraction of the cubic lattice during Li extraction causes low-temperature LiNi1/2Mn1/2O2 to have a cubic lattice rather than a layered structure with a pseudo-cubic lattice. The crystal structure of low-temperature LiNi1/2Mn1/2O2 with a cubic lattice and the Li extraction mechanism were elucidated from these results.

FABRICATION OF Ni1-xMxO (M = Li, Na) AND ITS THERMOELECTRIC PROPERTIES

Reaction behaviour of Ni 1− x M x O’s (M = Li, Na) formation and its thermoelectric properties

Reaction behaviour of Ni<sub>1−<i>x</i></sub>M<sub><i>x</i></sub>O’s (M = Li, Na) formation and its thermoelectric properties

Thermoelectric Performance Enhancement of Magnéli Phase Ti n O 2 n −1 Compacts by In Situ Reduction of TiO 2 with Charcoal Powder via Spark Plasma Sintering

Fabrication of Nanostructured Non-Stoichiometric TiO2-x by Spark Plasma Sintering for Enhancing Its Thermoelectric Properties

Fabrication of non-stoichiometric titanium dioxide and its thermoelectric properties

Fabrication And Thermoelectric Properties Of Magneli Phases By Adding Ti Into Tio2

Magnèli Phase Ti O2-1 Bulks Prepared by SPS Followed by Carbon Reduction and Their Thermoelectric Performance

Effect of Ni Substitution on Electrical and Thermoelectric Properties of LaCoO3 Ceramics

Synthesis and Characterization of LiNi1/3Mn1/3Co1/3O2 by Wet-Chemical Method

Fabrication and Thermoelectric Properties of Magneli Phases by Adding Ti into TiO<sub>2</sub>

Fabrication of Ti1-Xcrxoz and Analysis of Its Microstructure and Thermoelectric Properties

Power Factor Enhancement Induced by Bi and Mn Co-Substitution in NaxCoO2 Thermoelectric Materials

Facile synthesis of micrometer Li1.05Mn1.95O4 and its low temperature performance for high power lithium ion batteries

Influence of Synthetic Conditions on Structure and Electrochemical Performance of Li [ Ni1/3Co1/3Mn1/3 ] O2

Synthesis and electrochemical properties of a cubic polymorph of LiNi1/2Mn1/2O2 with a spinel framework

High-Temperature Thermoelectric Properties of Li-Y(Tixni1-X)(1-Y)O Ceramics

Fabrication and Performance Enhancement of TiO2-x Thermoelectric Material by In-Situ Reduction

Characterizations on the Structural and Electrochemical Properties of LiNi1/3Mn1/3Co1/3O2 Prepared by a Wet-Chemical Process

Preparation and characterization of LaMn 0.5 Co 0.5 O 3 –Ni 0.66 Mn 2.34 O 4 composite NTC ceramics

Structural evolution and formation mechanism of LiNi0.6Co0.2Mn0.2O2 during high-temperature solid-state synthesis