Abstract:The effect of nickel, tin, and indium additions in the eutectic Ag–28 wt.% Cu filler on the capillary and contact processes in brazing of VK94-1 and VK100 alumina ceramics and leucosapphire with VT1-0 titanium was examined. A special technique to study such processes was developed. This technique allows identifying, to the extent possible, the effect of different process parameters (heating rate, holding time, degree of vacuum, etc.) on the contact angles formed by metallic melts with different compositions on nonmetals in one experiment. High-temperature capillary and optical and scanning microscopy methods established that even small additions of nickel, tin, or indium to the eutectic Ag–Cu melt noticeably influenced the titanium dissolution rate and incipient wetting temperature of the nonmetallic substrate. Nickel additions were shown to enhance melt separation in the Ag–Cu–Ti system; in particular, the amount of the copper-based phase, eutectically melting with titanium above 870°C, increased. The effect of these additions in the Ag–28 wt.% Cu filler on the strength of brazed ceramic–ceramic joints produced using titanium foil inserts was studied. The results were discussed involving thermodynamic characteristics of the contacting structures. The role played by the type of chemical bonds in products resulting from interaction of the melt components and the solid substrate on the contact angle was shown. Brazed joints of alumina ceramics were made and used to determine the three-point-bending strength. The effect of various additions to the Ag–28 wt.% Cu filler on brazing strength was examined. Indium was found to be the most promising addition to the silver–copper filler as it allowed the brazing temperature to be controlled without a significant change in the mechanical strength of brazed joints.

Vacuum brazing of nickel-plated quartz fiber reinforced SiO_2 composites and Invar

Vacuum Brazing of C/C Composite and TiAl Intermetallic Alloy Using BNi-2 Brazing Filler Metal

Study on vacuum brazing of glass to kovar® alloy with Cu-Ni-Sn-P

Brazing of diamond to invar with Ag-Cu-Ti filler alloy: Wettability, microstructure and mechanical performance

Effects of nickel layer on interfacial micro-structure distribution and macro-mechanical properties for vacuum-brazed dissimilar steel joints

Study on Vacuum Brazing of Glass to Kovar (R) Alloy with Cu-Ni-Sn-P The optimum brazing time and temperature were sought to improve the shear strength and hermetic seal in the fabrication of a solar power system

Microstructure and Properties of Vacuum Melting Cr3C2-NiCr Coating by Nickel-based Brazing Foil

Joining Si3N4 ceramic to Invar using Mo mesh and Cu foil interlayer

Effect of brazing process on microstructure evolution and mechanical properties of Ti6Al4V/ZrO2 joints after laser surface treatment

Effect of Nickel, Tin, and Indium Doping of the Eutectic Silver–Copper Filler on the Capillary and Contact Processes in Brazing of Nonmetallic Alumina-Based Materials with Titanium

Brazing SiC ceramic to Zircaloy-4 using Zr-Ni filler alloy: Microstructure, mechanical properties and irradiation behavior

SiC fiber strengthened Si 14Ti high-temperature filler alloy for brazing SiC f /SiC and C/C composites

Interfacial microstructure and mechanical properties of ZTA/ZTA joints brazed with Ni-Ti filler metal

Preparation of NiTi/NiTiNb Laminated Alloys by Vacuum Brazing

Joints of Continuous Carbon Fiber Reinforced Lithium Aluminosilicate Glass Ceramics Matrix Composites to Ti60 Alloy Brazed Using Ti-Zr-Ni-Cu Active Alloy

Vacuum Brazing of Carbon Nanotube Bundles

Study on the microstructure and mechanical properties of Ti-Zr-Cu-Ni amorphous filler brazed Inconel 718 and 3D printed TC4 alloy

Microstructural characterization and mechanical properties of ZTA/ZTA joint brazed by Ni50Ti50 filler metal

Wetting and brazing of Cf/C composites with Si–Zr eutectic alloys: The formation of nano- and coarse-SiC reaction layers

Fabrication and characterization of SiC/Al composites prepared by laser powder bed fusion (LPBF) combined with vacuum pressure infiltration

Microstructure and properties of vacuum melting CoCrW coating by brazing foil