Abstract:The experiments on the torsion of the steel shaft were conducted on the machine Instron 55MT2 with a maximum torque of 220 N×m and a mass of 2500 N. The ends of the shaft clamped with collet-chucks. For the torsion we used the round cylindrical samples from a low-carbon steel with the Young’s modulus of 2×1011 Pa, the shear modulus of 7.752×1010 Pa, the Poisson’s ratio of 0.29, the yield strength of 524 MPa, the yield strength at shift of 302 MPa, the ultimate shear stress of 352 MPa, the ultimate shift of 0.18 and the plastic module at shift of 740 MPa. The torsion of the steel shafts and thick-walled pipes is widely used in the metallurgy, mechanical engineering and oilgas industry. For example, the shafts’ torsion is observed in the drive mechanisms of the sheet-straightening machines for the thin and thick steel sheets, in the rolling mills for the cold and hot steel sheets, in the drives of the rear wheels of motor transport, in the land and sea gas-oil drilling platforms and so on. Under the significant torque, the steel shafts can experience not only elastic, but also plastic deformation without the destruction. The experimental dependence of the shaft torque on the twisting angle gives researchers much more information about the mechanical properties of steel than the analogous experiments on the rupture of the steel shafts, since there is no neck formation during the torsion and the steel shaft does not collapse even at the very large twisting angles. The classical Ludwik’s and Nadai’s approximations for shear do not sufficiently accurately describe the shear deformation and are, therefore, not sufficiently effective for calculating the shaft torque. Therefore, the more accurate the straight and back Shinkin’s approximations are used below to describe the shear deformation. A special feature of calculating the dependence of the shaft torque on the shear angle is that the torque is calculated approximately as a power series, since the corresponding integrals are transcendental (cannot be calculated analytically). At the same time, the relative accuracy of the torque calculation is very high (about 10-6 %).

Interpretation of Torsional Shear Results for Nonlinear Stress–strain Relationship

A new model for analyzing nonlinear torsion behavior of concrete filled steel tube columns with rectangular section

Simplified method to identify full von Mises stress-strain curve of structural metals

ANALYSIS OF SECONDARY TORSION OF BIAXIAL FLEXURAL REINFORCED CONCRETE BEAMS

Study on the working mechanism and behavior of centrifuge concrete filled-steel tubular(CCFT) members subjected to torsion

CROSS SECTIONAL SHEAR STRAIN DISTRIBUTION OF RECTANGULAR CONCRETE FILLED STEEL TUBE COLUMNS SUBJECTED TO TORSION

Correlation between linear and nonlinear material functions under large amplitude oscillatory shear

Torque at elastic-plastic torsion of sheet-straightening machines’ steel shafts

Determination of Assumed Strain Hardening Relationship from Shear-Compression Model and Data Analysis

Identification of Shear Properties for Woven Fiber Reinforced Polymer Simulation

Study of Plastic Hardening-Large Deformed Torsion Test and Simulation

The large strain snap-through effect in free torsion of highly elastic soft thin-walled tubes with exact closed-form solutions

Comparison of theoretical elastic couple stress predictions with physical experiments for pure torsion

Numerical simulation of CFRP strengthened steel square hollow section (SHS) subject to torsion

Stress–strain curves of metallic materials and post‐necking strain hardening characterization: A review

The influence of the hardening curve of a material on the results of torsion tests of notched specimens

A molecular mechanics approach for analyzing tensile nonlinear deformation behavior of single-walled carbon nanotubes

On the Modeling of Extension-Torsion Experimental Data for Transversely Isotropic Biological Soft Tissues

Tension–torsion fracture experiments – Part II: Simulations with the extended Gurson model and a ductile fracture criterion based on plastic strain

Defining nonlinear rheological material functions for oscillatory shear

Identification of True Stress-Strain Curve of Thermoplastic Polymers under Biaxial Tension