Abstract:Low-voltage clock generation and modulation are important to have dynamic voltage scaling for low-power SoC design or to enable the chip to be directly powered by energy harvesters for IoT applications. Even though the supply voltage of an integer-N PLL has reached 0.4V [1], designing a robust fractional-N PLL under 0.5V is still challenging as both a high-performance phase detector (PD) and an effective ΔΣ quantization noise (Q-noise) reduction method are required at low voltage. As shown at the top of Fig. 14.7.1, the time resolution of a DTC is severely degraded as supply voltage decreases, and the use of a circuit’s intrinsic time delay as reference base is not stable over PVT variations. Even though voltage-domain compensation methods [2, 3] achieve lower noise and better linearity, they must first convert the phase error from the time domain to the voltage domain, which causes nonlinearity issues and consumes significant voltage headroom for ultra-low-voltage (ULV) operations. To the best of authors’ knowledge, the lowest supply voltage for a published fractional-N PLL is 0.5V, but it uses an on-chip voltage booster to supply a higher internal voltage for the TDC [4] or must use large decoupling capacitors for the TDC in product-level designs. Given the fact that the use of a large decoupling capacitor with supply regulation is required in practice to achieve robust in-band noise performance, a time-interleaving flip-flop phase detector (TI-FFPD) has been proposed as an efficient PD structure, which achieves high linearity and low reference spur for a ring-VCO-based integer-N PLL [5]. By leveraging the advantage of the TI-FFPD, this paper presents a sub-0.5V bias-current-free fractional-N PLL with a calibration-free voltage-mode phase interpolator (VPI) for Q-noise cancellation, achieving sub-600fs rms jitter and <-57dBc worse-case fractional spur at 2.4GHz output.

A Wide-Tuning Quasi-Type-I Pll with Voltage-Mode Frequency Acquisition Aid

Optimized System Design for Fully Integrated Fractional-N Pll

A 0.8 V Low Power Low Phase-Noise Pll

A C<inf>int</inf>-less Type-Ii PLL with &#x0394;&#x03a3; DAC Based Frequency Acquisition and Reduced Quantization Noise

An 8-14Ghz 180Fs-Rms DTC-Less Fractional ADPLL with ADC-Based Direct Phase Digitization in 40nm CMOS

An Ultra-Low-Voltage Bias-Current-Free Fractional- $N$ Hybrid PLL with Voltage-Mode Phase Detection and Interpolation

A 4.7ghz Synchronized-Multi-Reference PLL with In-Band Phase Noise Lower Than Reference Phase $\text{noise +20}\Text{logn}_{\mathrm{d}\mathrm{i}\mathrm{v}}$

A Low Power Sub-GHz PLL with Optimized Class-C Voltage-controlled Oscillator

A Low-Power Calibration-Free Fractional-N Digital Pll with High Linear Phase Interpolator

A Nonlinearity-Calibration-Free Reconfigurable ADPLL for General Purpose Frequency Modulation.

A Continuously Tunable Hybrid Lc-Vco Pll with Mixed-Mode Dual-Path Control and Bi-Level Delta-Sigma Modulated Coarse Tuning

25.6 A 70.5-to-85.5GHz 65nm phase-locked loop with passive scaling of loop filter

A Bias-Current-Free Fractional-N Hybrid PLL for Low-Voltage Clock Generation

14.7 A 0.45V 0.72mw 2.4ghz Bias-Current-Free Fractional-N Hybrid PLL Using a Voltage-Mode Phase Interpolator in 28nm CMOS

A 2.74&#x2013;5.37ghz Boosted-Gain Type-I PLL with &#38;#60;15% Loop Filter Area

A Fast Acquisition PLL with Wide Tuning Range

An Adaptive PLL Architecture to Achieve Fast Settling Time

A Wideband Fractional-N Frequency Synthesizer with Novel Self-Calibration Technique

A calibration-free multi-phase sampling Type-II PLL

A 2.6ghz ΔΣ Fractional-N Bang-Bang PLL with FIR-Embedded Injection-Locking Phase-Domain Low-Pass Filter

Design of the Fast Acquisition PLL with Wide Tuning Range