Abstract:Direct ink writing (DIW) and low-temperature sintering methods were applied to prepare Si2N2O-Si3N4 ceramics for radome materials. Lattices of Si-SiO2 green body were printed by DIW with 78 wt % solid portion of water-based Si-SiO2 slurry, in which silicon particles and silica fume were used as the solid portion and Methylcellulose (HPMC) was used as the dispersant. Effects of HPMC addition on stability and silica fume content on rheological properties of the slurry were studied, respectively. The pseudoplastic mechanism of the slurry was analyzed. The Si-SiO2 green bodies were sintered at 1250 °C–1400 °C in nitrogen. The effect of temperature on phase composition, microstructure, mechanical and dielectric properties of samples was investigated. With the HPMC addition of 0.12 wt% and the silica fume proportion of 30 wt% in solid portion, a stable and pseudoplastic slurry with the yield stress of 110.9 Pa was obtained, which is suitable for DIW. With the decrease of initial holding temperature, more N2 enters the sample and reacts with silicon and silica fume, promoting the generation of Si2N2O and Si3N4. The optimal condition yields Si2N2O-Si3N4 ceramics with apparent porosity of 42.73%, compressive strength of 24.7 MPa, dielectric constant of 4.89 and loss tangent of 0.0054. It is found that columnar Si3N4 comes from a direct reaction between silicon and N2, and fibrous Si2N2O is mainly generated by the reaction between silicon, SiO(g), and N2 through the chemical vapor deposition mechanism. Good dielectric properties are achieved due to high porosity, high proportion of Si2N2O phase and no residual silicon.

THE STUDY OF THE SLURRY PROPERTIES OF Si_3N_4 FOAM CERAMICS

Study on the Process of Si3N4 Ceramic with High Properties by Gel-casting

Si 3 N 4 slurry with high solid phase, low viscosity prepared via surface-oxidation and silane coupling agent modification hybrid method

Rheological Properties,dispersibility and Stability of Nano-Sic Based Aqueous Slurry

DISPERSIBILITY MECHANISM AND SPRAY DRYING OF SiC AQUEOUS SLURRY

Rheological properties and spray-drying behaviors of nano-SiC based aqueous slurry

The Effect of pH Value and Solid Concentration on the Properties of Cerium Oxide Slurry

Influence of surface oxide layer of SiC powder on the rheological properties of its slurry

Preparation of porous Si 3 N 4 ceramics via tailoring solid loading of Si 3 N 4 slurry and Si 3 N 4 poly-hollow microsphere content

Study on particle-stabilized Si3N4 ceramic foams

Preparation of High-Stability Ceramic Slurry with Gel Behavior for Stereolithography 3D Printing

Rheological properties and thixotropy model of concentrated aqueous silicon slurry for gel casting

De-stabilization Mechanism and in Situ Solidification of Alumina Slurry Dispersed in Silica Sol

Mechanical and dielectric properties of porous Si3N4 ceramics prepared by modified water‐based gel casting

Morphology Design of Porous Si2N2O Ceramics via Silica Poly-Hollow Microspheres

SPRAY PELLETIZATION PROPERTIES OF AQUEOUS SIC SLURRY

Study on Rheological Behavior of Micro/Nano-Silicon Carbide Particles in Ethanol by Selecting Efficient Dispersants

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Formation mechanism of stereolithography of Si3N4 slurry using silane coupling agent as modifier and dispersant

Effects of Powder Surface Modification and Amount of Oxide Additives on Rheological Property of Si<sub>3</sub>N<sub>4</sub> Aqueous Suspension

Fabrication and properties of Si2N2O-Si3N4 ceramics via direct ink writing and low-temperature sintering