Abstract:The thermal stability of the dual phase AlCrFeCoNiCu 0.5 high entropy alloy thin films at up to 600 °C under vacuum was studied through detailed characterization. The evolution of microstructure and chemical composition was revealed by X-ray diffraction, transmission Kikuchi diffraction and transmission electron microscopy . Also, the mechanical properties were measured by nanoindentation . Although the crystalline phase of all the HEA thin films was BCC-dominated, the FCC phase fraction increased from 16.6% (as-deposited) to 28.1% (600 °C-annealed). The as-deposited films exhibited a columnar morphology with an average grain size of 106.1 nm for length and 31.3 nm for width and remained the columnar shape until 600 °C. The columnar grains showed an increasing tendency of size at 200 °C (221.3 nm and 45.6 nm for length and width) and 400 °C (283.9 nm and 56.2 nm). At 600 °C, the columnar grain size decreased to 211.8 nm in length and 59.3 nm in width. Concurrently, the occurrence of new equiaxed grains was observed with an average diameter of 42.4 nm. The reduction of columnar grain size and the formation of equiaxed grains at 600 °C were explained based on the energy dispersive spectroscopy. Although no preferential evaporation was found, the elemental distribution revealed the formation of two secondary phases, i.e., Cu-rich FCC phase and Cr-rich BCC phase. The nanoindentation results indicated that the mechanical properties increased as the increase of annealing temperature. The hardness and elastic modulus of 600 °C-annealed sample were 8.5 ± 0.3 GPa and 205.4 ± 3.5 GPa, respectively, which were 10.4% and 41.5% higher than those of the as-deposited thin film. These findings are critical for a fundamental understanding of the microstructure and properties change of the dual-phase HEA thin films in high working temperatures.

Modifying crystallinity and mechanical properties of (CoCrNi) 95.8 Ce 4.2 medium entropy alloy films by post-annealing treatment

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

The microstructural evolution of dual phase high entropy alloy thin films by annealing

Influence of annealing on microstructures and mechanical properties of arc-deposited AlCrTiSiN coating

Effect of Annealing Temperature on the Microstructure and Mechanical Properties of CoCrFeNiNb0.2Mo0.2 High Entropy Alloy

Microstructure and Tensile Properties of Al0.5CoCrCuFeNi Alloys Produced by Simple Rolling and Annealing

Effects of Post Annealing on the Microstructure, Precipitation Behavior, and Mechanical Property of a (cocrni)94al3ti3 Medium-Entropy Alloy Fabricated by Laser Powder Bed Fusion

Influence of Annealing Treatment on the Microstructure and Mechanical Properties of Cold-Sprayed CoCrFeNiMn High Entropy Alloy

Effect of annealing temperature on the structure and properties of FeCoCrNiMo high-entropy alloy

Microstructure and Properties of Bulk Al0.5CoCrFeNi High-Entropy Alloy by Cold Rolling and Subsequent Annealing

Effect of Annealing on Microstructure and Mechanical Properties of an Ultrafine-Structured Al-containing FeCoCrNiMn High-Entropy Alloy Produced by Severe Cold Rolling

Effects of Annealing on Hardness, Yield Strength and Dislocation Structure in Single Crystals of the Equiatomic Cr-Mn-Fe-Co-Ni High Entropy Alloy

Influence of annealing temperatures on the microstructure and deformation behavior of a CrCoNi based medium-entropy alloy

Structural transformations during annealing of cold-worked high-entropy alloy Al0.3CoCrFeNi

Effect of Annealing Treatment on the Heterogeneous Microstructure and Properties of Cold-Rolled FeCoCrNiMn High-Entropy Alloy

Significant annealing-induced hardening effect in nanolaminated-nanotwinned (CrCoNi)97.4Al0.8Ti1.8 medium-entropy alloy by severe cold rolling

Annealing Improved Ductility and Fracture Toughness of Nanocrystalline Cu Films on Flexible Substrates

The Effect of Annealing on Mechanical Properties of Selective Laser Melted CoCrNi Medium-Entropy Alloy

Microstructure Evolution and Mechanical Properties of NiAlCrFeMo High Entropy Superalloy after Different Annealing Treatment

Effects of Substrate Temperature and Post-Annealing on Microstructure and Properties of (alcrnbsitiv)n Coatings

Effects of annealing at 800 and 1000 °C on phase precipitates and hardness of Al7Cr20Fe Ni73− alloys