Abstract:The thermal stability of the dual phase AlCrFeCoNiCu 0.5 high entropy alloy thin films at up to 600 °C under vacuum was studied through detailed characterization. The evolution of microstructure and chemical composition was revealed by X-ray diffraction, transmission Kikuchi diffraction and transmission electron microscopy . Also, the mechanical properties were measured by nanoindentation . Although the crystalline phase of all the HEA thin films was BCC-dominated, the FCC phase fraction increased from 16.6% (as-deposited) to 28.1% (600 °C-annealed). The as-deposited films exhibited a columnar morphology with an average grain size of 106.1 nm for length and 31.3 nm for width and remained the columnar shape until 600 °C. The columnar grains showed an increasing tendency of size at 200 °C (221.3 nm and 45.6 nm for length and width) and 400 °C (283.9 nm and 56.2 nm). At 600 °C, the columnar grain size decreased to 211.8 nm in length and 59.3 nm in width. Concurrently, the occurrence of new equiaxed grains was observed with an average diameter of 42.4 nm. The reduction of columnar grain size and the formation of equiaxed grains at 600 °C were explained based on the energy dispersive spectroscopy. Although no preferential evaporation was found, the elemental distribution revealed the formation of two secondary phases, i.e., Cu-rich FCC phase and Cr-rich BCC phase. The nanoindentation results indicated that the mechanical properties increased as the increase of annealing temperature. The hardness and elastic modulus of 600 °C-annealed sample were 8.5 ± 0.3 GPa and 205.4 ± 3.5 GPa, respectively, which were 10.4% and 41.5% higher than those of the as-deposited thin film. These findings are critical for a fundamental understanding of the microstructure and properties change of the dual-phase HEA thin films in high working temperatures.

Microstructure Evolution and Mechanical Properties of NiAlCrFeMo High Entropy Superalloy after Different Annealing Treatment

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

Effect of Annealing Temperature on the Microstructure and Mechanical Properties of CoCrFeNiNb0.2Mo0.2 High Entropy Alloy

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Al0.6CoFeNi2V0.5 High Entropy Alloy

Effect of annealing temperature on the structure and properties of FeCoCrNiMo high-entropy alloy

Effect of annealing treatment on microstructural evolution and compressive behavior of Al0.5CrFeNi2.5Si0.25 high-entropy alloy

Microstructural Evolution and Mechanical Properties of Al0.5CoCrFeNi High-Entropy Alloy after Cold Rolling and Annealing Treatments

Selective laser melting of AlCoCrFeMnNi high entropy alloy: Effect of heat treatment

Microstructure Evolution and Tensile Property of a CuMnFeCoNi High-Entropy Alloy During Thermomechanical Treatment

Achieving superior strength-ductility balance of Co–Cr–Fe–Ni high entropy alloy via annealing

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Effects of annealing at 800 and 1000 °C on phase precipitates and hardness of Al7Cr20Fe Ni73− alloys

Effect of Heat Treatment on Microstructure, Tensile Properties and High-Temperature Corrosion Resistance of the FeCrMnNi High Entropy Alloy

The microstructural evolution of dual phase high entropy alloy thin films by annealing

Microstructure and Mechanical Property Evolution during Annealing of a Cold-Rolled Metastable Powder Metallurgy High Entropy Alloy

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Study on annealing treatment of NbMoTaTiNi high-entropy alloy with ultra-high strength disordered-ordered transition structure for additive manufacturing

Microstructure evolution and mechanical behavior of a CoCrFeNiMn0.75Cu0.25 high-entropy alloy by thermo-mechanical treatment

Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Al0.6CoCrFeNi High-Entropy Alloy