Abstract:This paper introduces a finite-element analysis (FEA) on hybrid tubular K-joints with circular braces and square chord in stainless steel. The finite-element models (FEMs) were established by using the shell element S4R for circular braces, square chord and welds. The FEMs were validated by comparing the failure modes, failure strengths and joint deformation curves obtained from the experiments and FEA. A parametric study was carried out on 162 FEMs to evaluate the influences of brace diameter/chord width ratio ((beta = d1/b(0)), brace/chord thickness ratio (tau = t(1)/t(0)), chord width/thickness ratio (2 gamma = b(0)/t(0)), overlap ratio (0 = (q/p) x 100%) of overlapped tubular K-joints and eccentricity (e) of gapped tubular K-joints. The numerical results show that the joint strengths of overlapped tubular K-joints increased with the increment of the beta, tau and O-v, values, as well as the decrement of the 2 gamma value, while the joint strengths of gapped tubular K-joints increased with the increment of the beta and tau values, as well as the decrement of the 2 gamma and e values. The comparison of the failure strengths with design strengths demonstrates that the design formulae of CIDECT and Australian/New Zealand Standard (AS/NZS) are generally unconservative, whereas the design strengths determined by Eurocode (EC3) and Chinese Code are relatively close to the failure strengths for overlapped tubular K-joints. The design formulae of AS/NZS are generally unconservative, whereas the design formulae of CIDECT, EC3 and Chinese Code are generally conservative for gapped tubular K-joints. The design equations are proposed by introducing the correction factors that considered the influences of geometrical parameters of beta, tau, 2 gamma and O-v, which were validated to be accurate for hybrid tubular K-joints in stainless steel.

Numerical analysis on bearing capacity about the outer sleeve K-joint of rectangular pipe truss

EXPERIMENTAL RESEARCH AND FINITE ELEMENT ANALYSIS ON A WELDED JOINT WITH TUBES INTERSECTED AT TWO DIFFERENT POINTS

Ultimate Strength of the Circular Tubular X-joints

Parametric Study of In-Plane Ultimate Bearing Capacity of CFST Truss Rib Arch Bridge

Nonlinear Analysis on Ultimate Flexural Bearing Capacity of the N-Shaped Steel Tubular Joints

Failure Mechanism and Parameter Analysis of Outer Sleeve Joints under Reciprocating Load

Cyclic Behaviour of Double-Tube Buckling-Restrained Braces for Boiler Steel Plant Structures

Calculating the Ultimate Strength of a Tube–gusset KT Joint with 1/4 Ring Stiffener Plates

Experimental and Numerical Study on Ultimate Behaviour of High-Strength Steel Tubular K-joints with External Annular Steel Plates on Chord Circumference

Calculating the Nonlinear Stiffness and Ultimate Strength of Tube–Gusset Plate Joints in Circular Hollow Sections

Experimental study and theoretical analysis of ultimate strength of steel tubular K-joints of tall towers

Nonlinear Analysis for the Bearing Properties of Multiplanar Tubular Joints with Square and Circular Hollow Sections

Non-Linear Analysis of Ultimate Loading Capacity of Cast Tubular Y-Joints under Axial Loading

Ultimate Strengths of Triple-Ring-stiffened Tube-Gusset X-joints Considering the Effect of Chord Load

Non-linear Analysis on Cast Tubular T-joint Loaded by In-Plane Bending

Numerical Study of Hybrid Tubular K-joints with Circular Braces and Square Chord in Stainless Steel

Prediction on Ultimate Strength of Tube-Gusset KT-joints Stiffened by 1/4 Ring Plates Through Experimental and Numerical Study

Theoretical and Experimental Investigation on In-Plane Stability of Spatial Circular Tube Truss-Arches with Quadrangular Section

Post-buckling analysis of two-layer contact concentric tubular strings in pipe

Experimental and numerical study on static behaviour of uniplanar CFDST-CHS T-joints

Full-scale experimental research on tubular N-joints of square chords with circular braces