Abstract:This paper presents a finite-element (FE) investigation on the bearing capacity of stainless steel hybrid tubular K-joints with square braces and circular chord. The nonlinear finite-element (FE) models were developed and validated against the test results available in the literature, which were then used to conduct a parametric study including 162 models. The parametric study results showed that the joint strengths of the stainless steel hybrid tubular gapped K-joints increased when the β and τ values increased and when the 2γ and e values decreased. On the other hand, the joint strengths of overlapped K-joints increased when the β, τ, and Ov values increased and when the 2γ values decreased. Furthermore, the bearing capacities obtained from the parametric study were compared with the design strengths calculated from the current design guidelines. The comparison showed that the current design rules of Chinese Code (GB 50017–2017) were generally un-conservative for stainless steel hybrid tubular K-joints. The coefficient of variations (COVs) obtained from the comparison of EC3 (2005), AS/NZS (2001) and GB 50017 (2017) were very large. However, the design strengths calculated from the International Committee for the Development and Study of Tubular Structures (CIDECT) were relatively close to the FE strengths. Therefore, modified design rules are proposed in this paper. New design formulas were developed by applying correction factors (ψg and ψo) to the current design rules of CIDECT (2008) for carbon steel CHS tubular K-joints, considering the effects of key geometric parameters of β, τ, 2γ and Ov, respectively. The proposed design rules can accurately predict the bearing capacity of stainless steel hybrid tubular K-joints with square braces and circular chord, being only 1% conservative to the FE strengths.

Nonlinear Analysis for the Bearing Properties of Multiplanar Tubular Joints with Square and Circular Hollow Sections

NONLINEAR FINITE ELEMENT ANALYSIS FOR THE ULTIMATE STRENGTH OF MULTIPLANNAR TUBULAR JOINT

Load-carrying capacity of welded hollow spherical joints subject to combined planar tri-directional axial force and bending moment

Load-Carrying Capacity and Practical Calculation Method for Hollow Cylinder Joints Connected with H-Shaped Beams

Load-carrying Capacity and Practical Calculation Method of Welded Hollow Spherical Joints with Square Steel Tubes Subjected to Combined Axial Forces and Biaxial Bending Moments

EXPERIMENTAL RESEARCH AND FINITE ELEMENT ANALYSIS ON A WELDED JOINT WITH TUBES INTERSECTED AT TWO DIFFERENT POINTS

Simplified theoretical solution and practical calculation method for welded hollow spherical joints of rectangular hollow section members

Experimental study of the static behavior of tubular N-joints

Non-linear Analysis on Cast Tubular T-joint Loaded by In-Plane Bending

Non-Linear Analysis of Ultimate Loading Capacity of Cast Tubular Y-Joints under Axial Loading

Ultimate Strength of the Circular Tubular X-joints

Load-carrying Capacity and Practical Calculation Method of Welded Hollow Spherical Joints Connected with Square Steel Tubes

Non-linear Analysis on Axially Loaded Cast Tubular T-joints Including the Effects of Fillet Parameter

Nonlinear Analysis on Ultimate Flexural Bearing Capacity of the N-Shaped Steel Tubular Joints

Nonlinear Finite Element Analysis of Ultimate Strength on Tubular K-Joints:Square Chords and Circular Braces

Analysis on Influence Factors of Axial Strength of Circular Tubular TX-and TT-joints

Nonlinear behaviour and design of stainless steel hybrid tubular K-joints with SHS-to-CHS

Numerical Study of Hybrid Tubular K-joints with Circular Braces and Square Chord in Stainless Steel

Finite-element Analysis and Design of Stainless-Steel CHS-to-SHS Hybrid Tubular Joints under Axial Compression

RESEARCH ON THE BREAKAGE MODE AND ANALYTIC MODEL OF CIRCULAR TUBULAR X-JOINTS

Calculating the Nonlinear Stiffness and Ultimate Strength of Tube–Gusset Plate Joints in Circular Hollow Sections