Abstract:Polycrystalline Ni3Al-based superalloy with up to 70% <math>γ′</math> phase owns excellent strength at around 1100 °C. It has been successfully used as a substitute for turbine blade crown, which is one of the aircraft components working in the severest environment (i.e., sometimes nearly overheating). However, few studies concentrate on the coarsening resistance and phase thermal stability in this newly designed polycrystalline superalloy at the working temperature, hence, directional coarsening behavior of primary <math>γ′</math> <math>(γI′)</math> has remained restricted. This paper investigated directional coarsening behavior of <math>γI′</math> during aging treatment (1100 °C) after overheating at 1270 °C with furnace cooling (SFA), air cooling (SAA) and water cooling (SWA) respectively. It clearly showed that <math>γI′</math> grew into lamellar and gradually became irregular during the directional coarsening process. Moreover, its morphological combination mode was illustrated. Since parallel short lamellar <math>γI′</math> connected each other, long lamellar formed. When perpendicular long lamellar <math>γI′</math> connected each other, it became L-type or T-type, i.e., precursor of irregular <math>γI′</math>. The kinetics of directional coarsening regime of <math>γI′</math> was in line with the matrix-diffusion-controlled (MDC) theory according to the evaluation of <math>γI′</math> size. This was caused by higher migration of <math>γI′</math> interfaces than the diffusion of solute elements. It was also confirmed that driving force of directional coarsening mainly depended on the competition of elemental diffusion, lattice misfit distribution and <math>γ</math> channel distance.

Investigation on γ′ stability in CoNi-based superalloys during long-term aging at 900 °C

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

The Temperature Dependence of High-Temperature Strength and Deformation Mechanism in a Single Crystal CoNi-base Superalloy

Effects of Al content on microstructures and high-temperature tensile properties of two newly designed CoNi-base superalloys

High-throughput exploration of alloying effects on the microstructural stability and properties of multi-component CoNi-base superalloys

Effect of μ precipitation and γ′ evolution on intra/intergranular strength of Ni-Co-Cr-based superalloys after 800 °C thermal exposure

Effect of alloying elements on the coarsening rate of γʹ precipitates in multi-component CoNi-based superalloys with high Cr content

Understanding the composition-dependent stability of η phase for future Ni-Co-based superalloys

Atomic size effect of alloying elements on the formation, evolution and strengthening of γ′-Ni3Al precipitates in Ni-based superalloys

Directional coarsening behavior of primary γ′ phase in Ni3Al-based superalloy during aging heat treatment

Coarsening kinetics of γ′ phase in isothermal aged high Al content Ni–17 at.% Al alloy

Effects of Alloying Elements on the Microstructure of Precipitation Strengthened Co-based Superalloys

The effects of Ti and Ta on the microstructure and high temperature deformation mechanisms of the CoNi-based superalloys

Theoretical Exploration of Alloying Effects on Stabilities and Mechanical Properties of γʹ Phase in Novel Co–Al–Nb-Base Superalloys

Microstructures and Mechanical Properties of a L1 2 -structured precipitation Strengthened Co-based Superalloy

Enhancing structural stability of γ′-Co 3 (Al, Nb) phases: The key role of anti-site defects

Effect of microstructure on temperature dependence of deformation behavior in polycrystalline CoNi-based superalloy

Development of low-density γ/γ′ Co–Al–Ta-based superalloys with high solvus temperature

Microstructure and mechanical properties of a new Ni–Co based superalloy at intermediate temperatures

Thermal stability of carbides in a Ni-based single crystal superalloys

Plastic Deformation Behaviors and Mechanical Properties of Advanced Single Crystalline CoNi-base Superalloys