Abstract:Through the incorporation of phosphorus (P) as a third component, an in-situ formation of a magnetic phase with a nanotwin structure was achieved. The utilization of selective laser melting (SLM) enabled the synthesis of a Cu-Fe-P immiscible alloy that exhibits an integrated structure and function. The microstructure predominantly consists of a magnetic heterogeneous Fe-P-rich phase, comprising a mixture of Fe2P and a small quantity of Fe3P, which is distributed within the & epsilon;-Cu Cu-rich matrix in alternating "fiber -layer" and "particle-shape" forms. Additionally, the fibrous Fe2P phase exhibited precipitation of a-Fe, while the Fe-P-rich phase experienced the precipitation of high-density nanotwinned Cu (nt-Cu) particles. The microstructure density and structural characteristics of Cu-Fe-P immiscible alloys were enhanced through the adjustment of laser energy density, leading to improvements in their mechanical and magnetic prop-erties. It was observed that the microstructure density initially increased and then decreased with increasing laser energy density. The highest relative density of the Cu-Fe-P immiscible alloy microstructure (98%) was achieved at a laser energy density of 53 J/mm3. Furthermore, the influence of laser energy density on the mechanical and soft magnetic properties of Cu-Fe-P immiscible alloys was examined. The findings indicate that the mechanical and soft magnetic properties of these alloys are affected by the laser energy density. The findings indicate that the compact Cu-Fe-P immiscible alloys exhibit favorable compression mechanical properties and soft magnetic properties. Specifically, the ultimate compressive stress can reach 890.5 & PLUSMN; 20 MPa, while the failure strain can reach 20.5 & PLUSMN; 2%. Additionally, the coercivity is observed to be as low as 20.0 Oe, the magnetic saturation strength as high as 93.5 emu/g, and the residual magnetization at 1.1 emu/g.& COPY; 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Effects of adding Cu on the microstructure and properties of in-situ alloyed Fe–Cr–Co permanent magnets by laser powder bed fusion

Texture, Microstructure, and Properties of Fe-Cr-Co Permanent Magnetic Alloy Fabricated by Laser Powder Bed Fusion In-Situ Alloying

In Situ Alloying of Fe-Cr-Co Permanent Magnet by Selective Laser Melting of Elemental Iron, Chromium and Cobalt Mixed Powders

Effects of Cu Nanopowders Addition on Magnetic Properties and Corrosion Resistance of Sintered Nd–Fe–B Magnets

Effect of Laser Energy Density on Microstructure and Properties of High Strength and Magnetic Cu-Fe-P Immiscible Alloys Fabricated by Laser Selective Melting

Understanding the role of Cu element in nanocrystalline hot deformed Nd-Fe-B magnets

The role of Cu content on structure and magnetic properties of Fe–Si–B–P–Cu nanocrystalline alloys

Effect of Si Element and TiB2 Nucleating Agent on Microstructure and Magnetic Properties of Cu-based Immiscible Composites by Laser Melting Deposition

Roles of Cu in Fe-based Soft Magnetic Nanocrystalline Alloys with High Fe Content

Effect of Laser Energy Density on Microstructure and Properties Cu–Fe–P Immiscible Alloys Fabricated by Laser Selective Melting: Heterogeneous and High Strength and Magnetic

Effects of Ti and (or) Cu on microstructures and magnetic properties of sintered Nd-Fe-B magnets

Investigation of glass forming ability, crystallization behavior, and soft magnetic properties of Fe–B–P–C–Cu alloy ribbons

Laser powder bed fusion of a nanocrystalline Finemet Fe-based alloy for soft magnetic applications

Optimization of Crystallization Behavior and Soft Magnetic Properties of the Si-free Fe-B-P-C-Cu Nanocrystalline Alloys by Cu Content Tuning

Effect of Cu and Cu–Ti additions on the microstructures and magnetic properties of Nd2Fe14B–α-Fe nanocomposite magnets

Effects of Pr-Cu-Ti intergranular addition on microstructure and magnetic properties of heavy-rare-earth-free Nd-Fe-B sintered magnets

Fe content influence on the microstructure of solution-treated Sm-Co-Fe-Cu-Zr alloys

Coercivity enhancement of NdFeB sintered magnets by low melting point Dy32.5Fe62Cu5.5 alloy modification

Effect of post-sintering annealing on microstructure and coercivity of Al85Cu15-added NdFeB sintered magnets

Crystallization behavior, soft magnetic properties and good bending ductility of high Fe content FeSiBCuPC alloys induced by composition design

Effect of copper and titanium addition on microstructures and magnetic properties of sintered Nd22Fe71B7 magnets