Abstract:The CFRP/Ti6Al4V composite has excellent properties of CFRP and Ti6Al4V. Therefore, they are widely used in aerospace and some military fields. The laminated structure of CFRP/Ti6Al4V composite is different from the traditional homogeneous workpiece, and the properties of each layer are diverse, so the processing performance is poor. The experimental research cost of CFRP/Ti6Al4V composites is relatively high and has certain limitations. The finite element method is a promising alternative. In the research, a finite element model combining the macro and micro with the fiber orientation of 90 degrees was established. By combining the mechanism of exit burr formation in the cutting direction of Ti6A14V and the delamination mechanism of CFRP composites, a new mechanical model was proposed for CFRP/Ti6Al4V composites during this study, and it was found that there is not a linear relationship between the rake angle and the delamination of CFRP/Ti6Al4V composites during the cutting process. The results show that the delamination damage of CFRP/Ti6Al4V composites is serious when the rake angle is 4 degrees similar to 10 degrees. The delamination damage is light when the rake angle is 0 degrees similar to 4 degrees. And the delamination damage is the smallest when the rake angle is 10 degrees similar to 20 degrees. In the cutting process, the tremor of the Ti6Al4V phase is also an important factor for delamination. During the extrusion of Ti6Al4V relative to the CFRP phase, the fragmentation of the epoxy matrix leads to brittle fracture of the carbon fibers and shear damage can occur. The brittle fracture height is minimum when the rake angle is 16 degrees. The shear damage height is minimum when the rake angle is 10 degrees. The tremor of Ti6Al4V phase is also an important factor for delamination damage. The fracture of the epoxy resin matrix leads to brittle fracture and shear damage of carbon fiber. The brittle fracture height has a linear relationship with the fracture height of epoxy resin. When the cutting sequence is CFRP -> Ti6Al4V, a better surface quality can be obtained, effectively avoiding carbon fiber brittle fracture. Therefore, the rake angle and cutting sequence are of great importance for processing CFRP/Ti6Al4V composites. Therefore, it is of reference significance for the machining of 90 degrees fiber orientation.

Carbon Fiber Breakage Mechanism in Aluminum (Al)/Carbon Fibers (CFs) Composite Sheet during Accumulative Roll Bonding (ARB) Process

Preparation, Microstructure, and Mechanical Properties of Aluminum Matrix Composite by Accumulating Roll Bonding Method

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Rolling preparation process and interface toughening mechanism of Al/CFRTP/Al composite laminates

Effect of Asymmetric Accumulative Roll-Bonding process on the Microstructure and Strength Evolution of the AA1050/AZ31/AA1050 Multilayered Composite Materials

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Mechanical, microstructural, and textural evaluation of aluminum-MWCNT composites manufactured via accumulative roll bonding at ambient condition

Effect of the Cross Accumulative Roll Bonding on the Corrosion Behaviour of AA6082/AA7204 Composite Sheets

Microstructure and Mechanical Properties of the Mg/Al Laminated Composite Fabricated by Accumulative Roll Bonding (Arb)

Forming limit diagrams and mechanical properties of AA1050/Ti CP2 multilayered composite produced by the accumulative roll bonding technique

Interfacial bonding mechanism of Cu/Al composite plate produced by corrugated cold roll bonding

Effect of cumulative deformation and interlayer mechanical properties on bonding strength of corrugated interface steel/aluminum composite plate

Evolution of Microstructure, Texture and Mechanical Properties for Multilayered Al Matrix Composites by Accumulative Roll Bonding

Microstructure and Mechanical Properties of AA1050/AA6061 Laminated Composites Fabricated through Three-Cycle Accumulative Roll Bonding and Subsequent Cryorolling

Effect of ARB process on the plane stress fracture toughness, creep properties and forming limit diagram of Aluminum/BN/Copper composite strips

High Strength and Thermal Stability of Multilayered Cu/Al Composites Fabricated Through Accumulative Roll Bonding and Cryorolling

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Response mechanism of matrix microstructure evolution and mechanical behavior to Mg/Al composite plate by hard-plate accumulative roll bonding

The crucial role of accumulated strain and Cu content on the electrical, thermal, tensile, fracture, and microstructure characteristics of Al/Cu multi-layered composites subjected to SPD

Effect of normal load and strain accumulation on tribological properties of Al3003/St12 multilayered composite produce by severe plastic deformation

Delamination and Chip Breaking Mechanism of Orthogonal Cutting CFRP/Ti6Al4V Composite