Abstract:Hydrogen energy is the clean energy with the most potential in the 21st century. The microchannel reactor for methanol steam reforming (MSR) is one of the effective ways to obtain hydrogen. Ceramic materials have the advantages of high temperature resistance, corrosion resistance, and high mechanical strength, and are ideal materials for preparing the catalyst support in microchannel reactors. However, the structure of ceramic materials is hard and brittle, and the feature size of microchannel is generally not more than 1 mm, which is difficult to process using traditional processing methods. Diamond wire saw processing technology is mainly used in the slicing of hard and brittle materials such as sapphire and silicon. In this paper, a microchannel with a periodic corrugated microstructure was fabricated on a ceramic plate using diamond wire sawing, and then as a catalyst support when used in a microreactor for MSR hydrogen production. The effects of wire speed and feed speed on the amplitude and period size of the periodic corrugated microstructure were studied using a single-factor experiment. The microchannel surface morphology was observed via SEM and a 3D confocal laser microscope under different processing parameters. The microchannel samples obtained under different processing parameters were supported by a multiple impregnation method. The loading strength of the catalyst was tested via a strong wind purge experiment. The experimental results show that the periodic corrugated microstructure can significantly enhance the load strength of the catalyst. The microchannel catalyst support with the periodic corrugated microstructure was put into the microreactor for a hydrogen production experiment, and a good hydrogen production effect was obtained. The experimental results have a positive guiding effect on promoting ceramic materials as the microchannel catalyst support for the development of hydrogen energy.

Direct ink writing of 3D SiC scaffold as catalyst support for thermally autonomous methanol steam reforming microreactor

Structural optimization of 3D printed SiC scaffold with gradient pore size distribution as catalyst support for methanol steam reforming

Direct Ink Writing of Hierarchical Porous SiC Ceramics As Catalyst Support for Hydrogen Production

A novel thermally autonomous methanol steam reforming microreactor using SiC honeycomb ceramic as catalyst support for hydrogen production

An Innovative Micro-Channel Catalyst Support with a Micro-Porous Surface for Hydrogen Production Via Methanol Steam Reforming

Hydrogen production in microreactor using porous SiC ceramic with a pore-in-pore hierarchical structure as catalyst support

Development of ceramic-based 3D staggered microchannel catalyst support used in MSR microreactor for hydrogen production

A Thermally Autonomous Methanol Steam Reforming Microreactor with Porous Copper Foam As Catalyst Support for Hydrogen Production

CuO–ZnO catalyst decorated on porous CeO2-based nanosheets in-situ grown on cordierite for methanol steam reforming

Fabrication of Ceramic Microchannels with Periodic Corrugated Microstructures as Catalyst Support for Hydrogen Production via Diamond Wire Sawing

Vat photopolymerization of polymer-derived SiC ceramic with triply period minimal surface structure for hydrogen production

Numerical modeling of triply period minimal surface structures with catalyst coating for hydrogen production of methanol steam reforming

Highly controlled structured catalysts for on-board methanol reforming

Numerical Modeling of Microchannel Reactors with Gradient Porous Surfaces for Hydrogen Production Based on Fractal Geometry

Construction of porous Cu/CeO2 catalyst with abundant interfacial sites for effective methanol steam reforming

A Micro-Reactor with Micro-Pin-fin Arrays for Hydrogen Production Via Methanol Steam Reforming

Structured nanoporous Cu/ZnO catalysts for on-board methanol steam reforming prepared by laser powder bed fusion and dealloying

Development of Multilevel Amplified Methanol Steam Reforming Microreactor with High Hydrogen Production Rate

Preparation of a Durable CuO/ZnO/CeO2/ZrO2 Catalyst on an SiC Support by an Inverse Microemulsion/Precipitation Method for Methanol Steam Reforming

A flow-through catalytic membrane micro-reactor for hydrogen production by methanol steam reforming

Development of Centrifugal Coating Device to Load CuZnZr/γ-Al2O3 Catalyst on Porous Substrates for Methanol Steam Reforming