Abstract:Silicon carbon nitride thin films were deposited on Co-Cr alloy under varying deposition conditions such as sputtering power and the partial pressure ratio of N(2) to Ar by radio frequency and direct current magnetron sputtering techniques. The chemical bonding configurations, surface topography and hardness were characterized by means of X-ray photoelectron spectroscopy, atomic force microscopy and nano-indentation technique. The sputtering power exhibited important influence on the film composition, chemical bonding configurations and surface topography, the electro-negativity had primary effects on chemical bonding configurations at low sputtering power. A progressive densification of the film microstructure occurring with the carbon fraction was increased. The films prepared by RF magnetron sputtering, the relative content of the Si-N bond in the films increased with the sputtering power increased, and Si-C and Si-Si were easily detachable, and C-O, N-N and N-O on the film volatile by ion bombardment which takes place very frequently during the film formation process. With the increase of sputtering power, the films became smoother and with finer particle growth. The hardness varied between 6 GPa and 11.23 GPa depending on the partial pressure ratio of N(2) to Ar. The tribological characterization of Co-Cr alloy with Si-C-N coating sliding against UHMWPE counter-surface in fetal bovine serum, shows that the wear resistance of the Si-C-N coated Co-Cr alloy/UHMWPE sliding pair show much favourable improvement over that of uncoated Co-Cr alloy/UHMWPE sliding pair. This study is important for the development of advanced coatings with tailored mechanical and tribological properties. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved.

Effect of deposition rate on anti-reflection and wettability properties of RF magnetron sputtering SiCON thin film

Effect of N2 reactive gas flow rate on the structural, optical and wettability properties of silicon carbon oxynitride thin films

Properties of amorphous SiO2 films prepared by reactive RF magnetron sputtering method

Optical Properties Study of Silicon Oxynitride Films Deposited by RF Magnetron Sputtering

Deposition of Dense SiO2 Thin Films for Electrical Insulation Applications by Microwave ECR Plasma Source Enhanced RF Reactive Magnetron Sputtering

Effect of High Deposition Rate on Chemical Bonds and Properties of SiN Film

Magnetron sputtering technique for analyzing the influence of RF sputtering power on microstructural surface morphology of aluminum thin films deposited on SiO2/Si substrates

Investigation of Amorphous-Sic Thin Film Deposition by RF Magnetron Sputtering for Optical Applications

The Structure, Surface Topography and Mechanical Properties of Si–C–N Films Fabricated by RF and DC Magnetron Sputtering

Fabrication and characterization of magnetron sputtered SAC305 thin films

Effect of assistant RF plasma on structure and properties of SiCN thin films prepared by RF magnetron sputtering of SiC target

Influence of Sputtering Process on the Deposition and Optical Properties of Sicn Films

Characterization of low-dielectric-constant SiCON films grown by PECVD under different RF power

Nanostructure and Optical Properties of Sio2 Films Prepared by Reactive Midfrenquency Magnetron Sputtering

Structural and Electrical Properties of A Metallic Rough-Thin-Film System Deposited on Liquid Substrates

Effect of Oxygen Flow Rate on Microstructure Properties of SiO2 Thin Films Prepared by Ion Beam Sputtering

Influence of radio frequency magnetron sputtering parameters on the structure and performance of SiC films

Influence of Substrates on the Microstructure and Electrical Properties of Si/Mo Thin Films

Impact of H-Related Chemical Bonds on Physical Properties of SiNx:H Films Deposited via Plasma-Enhanced Chemical Vapor Deposition

Structural and Mechanical Properties of CrN Thin Films Deposited on Si Substrate by Using Magnetron Techniques

Thin films of silicon nitride deposited at room temperature by non-reactive magnetron sputtering: radiofrequency power and deposition time influence on the formation of α-Si3N4 and its optical properties