Abstract:Amorphous alumina films are isotropic and have no grain boundaries, which make them have smooth surfaces, excellent properties, and wide applications in protective coatings, catalysis, and microelectronics. However, high-quality alumina films were usually prepared by vapor-phase approaches which need expensive equipment and long production time. Additionally, amorphous films are long-range disordered, which makes the study of structure–property relationships challenging. Here, a simple sol–gel method is employed to obtain high-quality amorphous Al2O3 thin films. The microstructure, morphology, and mechanical properties of amorphous Al2O3 thin films were systematically investigated. All the Al2O3 thin films heat-treated at 600–800∘C are in amorphous state with ultrasmooth surface (Ra values about 0.29–0.43 nm) and high mechanical properties (elastic modulus ∼170[Formula: see text]GPa, hardness ∼20[Formula: see text]GPa). The mechanical properties (E and H) of Al2O3 films gradually increase with the increase of heat-treating temperature. Additionally, the Al coordination of the amorphous alumina films are analyzed by solid-state NMR and correlated with the mechanical properties. The results show that in amorphous alumina, the presence of tetrahedral Al ([4]Al) and octahedral Al ([6]Al) is helpful to improve the mechanical properties, while the five-coordinated Al ([5]Al) is not conducive to improve the mechanical properties. The results demonstrate that sol–gel method is an attractive alternative to time-consuming and expensive vapor-phase approaches and are useful for scale-up to applications and research of amorphous alumina films.

Effect of formic-acid-to-acetic-acid ratio on the structure and spinnability of aqueous aluminium sol of alumina fibre

Electrospun LaAlO3 nanofibers from different solvent systems

Synthesis and characterization of sol-gel derived continuous spinning alumina based fibers with silica nano-powders

Effect of the alumina and silica source mixing procedure on the microstructural evolution of alumina-mullite composite fibers prepared by sol–gel method

The Microstructure, Morphology, and Mechanical Properties of Sol-Gel-derived Amorphous Aluminum Oxide Films

Effect of Al2o3/Sio2 Ratio on the Viscosity and Structure of Slags

Structure, thermal stability and spinnability of the CaO-MgO-Al2O3-SiO2 glasses with SiO2 replaced by Al2O3

Effects of electrostatic polarities on the morphology of electrospun oxide nanofibers: A case study on alumina-based nanofibers

Synthesis and Characterization of Rich Silica Mullite Fibers by Sol–Gel Method Using Aluminum Lactate and Silica Sol

Synthesis and Characterisation of Alumina Fibres Using Organic/Inorganic Composite Sol

One-dimensional electrospun alumina borate ceramics: transformation from fiber-like structure to ribbon-like structure at the increased concentrations of precursor sol

Effect of silica sol on phase transition of alumina-mullite fibers

Preparation of Mullite Fibres by Sol–gel Processes Using Aluminium Carboxylates and Tetraethylorthosilicate

Removal of hydroxyl groups and its influence on the microstructures evolution of alumina-mullite fibers fabricated by sol-gel process

Improvement of interface between Al and short carbon fibers by α-Al2O3 coatings deposited by sol–gel technology

Effect of alumina sol on the preparation of magnesia‐alumina spinel foam ceramics by foaming‐sol method

Effect of residual carbon on the phase transformation and microstructure evolution of alumina-mullite fibers prepared by sol-gel method

Effects of SiO2 Addition on Phase Transition and Microstructure Evolution of Alumina Fibers Prepared Using the Sol-Gel Method

Continuous aluminum oxide-mullite-hafnium oxide composite ceramic fibers with high strength and thermal stability by melt-spinning from polymer precursor

High concentration of organic solvents in aluminum MAO: A study of structural and tribological property

Effects of Alumina Sols on the Sintering of Α-Alumina Ceramics