A blind comparison of the effectiveness of endoscopic ultrasonography and endoscopy in staging early gastric cancer.

T. Savides

IF: 10.396

2000-05-01

Gastrointestinal Endoscopy

Abstract:

What problem does this paper attempt to address?

Effect of support texture properties on Ni-Fe/γ-Al_2O_3 catalyst structure and catalytic performance for CO methanation

LIU Jun,MENG Fan-hui,ZHONG Peng-zhan,JI Ke-ming,LI Zhong

2013-01-01

Abstract:Ni-Fe/γ-Al2 O3 catalysts with four different γ-Al2 O3 supports were prepared by incipient impregnation and characterized by XRD,BET and H2-TPR.Catalytic behaviors of the catalysts for low-temperature CO methanation were investigated in a slurry reactor.The results showed that the surface texture properties of γ-Al2 O3 supports had great impact on distribution of Ni reactive species and methanation activity.Moderate specific surface area(192m2/g) and pore size(5.8 nm) of γ-Al2 O3 was favor for the dispersion of active component,resulting in a higher amount of β-NiO and smaller Ni crystal particle size,which increased active sites,thus having better methanation activity and stability,with a CO conversion of 97.0% and a CH4 selectivity of 89.0%.However,the catalyst prepared by high silica γ-Al2 O3 support with larger specific surface area contained a great amount of α-NiO,which was inclined to agglomerate in the reduction process,resulting in low catalytic activity and stability,with a CO initial conversion of 85.5% and rapid deactivation after 17 hours.
Metal-Organic Framework-Templated Synthesis of Nickel-Alumina Nanocatalysts Improves Catalyst-Support Interaction for Higher Activity and Stability in Biogas Reforming under Controlled Oxidizing Conditions

Arisha Sharma,Prakash Biswas,Meenesh R. Singh

DOI: https://doi.org/10.1021/acsami.4c12538

IF: 9.5

2024-11-28

ACS Applied Materials & Interfaces

Abstract:Tri-reforming methane with CO(2), O(2), and H(2)O mixtures requires a delicate balance of dry-reforming, partial oxidation, and steam-reforming reactions to improve the CO(2) conversion and H(2)/CO ratio. Nickel-alumina has been reported before for the tri-reforming of methane, although at higher temperatures (>900 °C). This is because the current approaches for nickel-alumina synthesis are ineffective in generating stronger catalyst-support interactions necessary to maintain higher active sites...

materials science, multidisciplinary,nanoscience & nanotechnology
Effect of Modified Alumina Support on the Performance of Ni-Based Catalysts for CO2 Reforming of Methane

Salwa Bader Alreshaidan,Ahmed A. Ibrahim,Anis H. Fakeeha,Abdulaziz M. Almutlaq,Fekri Abdulraqeb Ahmed Ali,Ahmed S. Al-Fatesh

DOI: https://doi.org/10.3390/catal12091066

IF: 3.9

2022-09-19

Catalysts

Abstract:The CO2 reforming of methane to syngas was examined over five different supported catalysts. In this study, 5% Ni was used as the active metal part of the catalyst. To better comprehend the impact of the supports on the catalytic properties, 5% Ni-based catalysts were characterized using nitrogen adsorption–desorption isotherms, XRD, H2-TPR, CO2-TPD, TGA, TPO, FTIR, and Raman. The results showed that the catalyst support with the highest surface area provided the best catalytic activity. The acquired CH4 and CO2 conversions at 700 °C were 58.2% and 67.6%, respectively, with a hydrogen/carbon ratio of 0.85. The TGA investigation of the high-surface-area sample produced a minimum carbon deposition of 11.2 wt.%, and in the CO2-TPD investigation, the high-surface-area sample exhibited the absence of a peak in the strong-basic-sites zone. The formation of NiAl2O4 spinel, moderate basicity, and the high surface area explained the outperformance of the high-surface-area catalyst sample.

chemistry, physical
Facile Route for Synthesizing Ordered Mesoporous Ni–Ce–Al Oxide Materials and Their Catalytic Performance for Methane Dry Reforming to Hydrogen and Syngas

Ning Wang,Kui Shen,Lihong Huang,Xiaopeng Yu,Weizhong Qian,Wei Chu

DOI: https://doi.org/10.1021/cs4003113

IF: 12.9

2013-01-01

ACS Catalysis

Abstract:A series Of ordered mesoporous Ni-Ce-Al composite oxides with various cerium contents were synthesized via a one-pot route: evaporation-induced self-assembly (EISA) strategy and tested in methane dry reforming for hydrogen and synthesis gas production. Using, this method, the hydrophobic nickel precursor was directly incorporated into the hydrophobic cores of surfactant micelles,, and thus, the highly dispersed Ni nanoparticles were Stabilized inside the mesopore Channels' of an alumina matrix. For comparison, Ni-based catalysts were also prepared by a traditional impregnation method. The characterization results confirmed that the ordered mesostructiires were well maintained in all of the cerium-incorporated Ni-Al materials (Ce/(Ce + Al) molar ratio <= 3%). The catalyst with a Ce/(Ce + Al) ratio of 1% exhibited the highest catalytic activity (with CO2 and CH4 initial conversions being 70% and 68% at 700 degrees C, respectively) and remained stable in a methane dry reforming reaction. This improved activity can be attributed to the large surface area and high dispersion and reducibility of Ni nanoparticles,which were Stable because of the stable alumina framework and high oxygen mobility in these Cerium-containing samples. Resistance to carbon deposition was found over the Ni-Ce-Al Catalyst, whereas amounts of graphitic carbon species were found over the Ni-impregnated catalysts, which was responsible for deactivation.
One‐pot Synthesis of Ordered Mesoporous NiCeAl Oxide Catalysts and a Study of Their Performance in Methane Dry Reforming

ning wang,zhenxin xu,jie deng,kui shen,xiaopeng yu,weizhong qian,wei chu,fei wei

DOI: https://doi.org/10.1002/cctc.201300720

IF: 4.5

2014-01-01

ChemCatChem

Abstract:Ordered mesoporous NiAl and NiCeAl catalysts with different Ce/Al molar ratios were facilely synthesized by using the improved evaporation-induced self-assembly method. The characterization results confirmed that the ordered mesoporous structure was well sustained in the Ce-incorporated NiAl materials (Ce/Al molar ratio<4%). Compared with NiAl mesoporous materials, Ce-incorporated mesoporous materials demonstrated higher specific surface areas, larger pore volumes, and more uniform pore sizes. The catalytic test conducted by using methane dry reforming revealed that compared with NiAl catalysts, all the Ce-promoted catalysts demonstrated improved initial catalytic activity, which was due to the high dispersion and the high reduction degree of active Ni species in NiCeAl catalysts. The stable alumina framework, confinement effect of ordered mesopores, and high oxygen mobility contributed to the improved catalytic stability of NiCeAl catalysts. For comparison, the mesoporous NiCeAl catalyst (denoted as NiCeAl-IMP) was also prepared by using the conventional impregnation method. The agglomeration of Ni particles was observed during the stability test for the Ni-impregnated catalyst, which accelerated the rate of carbon deposition. The NiCeAl catalyst (Ce/Al molar ratio=1%) demonstrated excellent resistance to the formation of graphitic carbon species owing to the redox property, while a large amount of graphitic carbon species was deposited over the NiAl sample, which was responsible for deactivation.
Ordered Mesoporous Alumina Supported Nickel Based Catalysts for Carbon Dioxide Reforming of Methane

Leilei Xu,Huahua Zhao,Huanling Song,Lingjun Chou

DOI: https://doi.org/10.1016/j.ijhydene.2012.01.105

IF: 7.2

2012-01-01

International Journal of Hydrogen Energy

Abstract:Ordered mesoporous alumina facilely synthesized via improved evaporation-induced self-assembly (EISA) strategy was provided with large specific surface area, big pore volume, uniform pore size and excellent thermal stability. The obtained mesoporous material was used as the carrier of the Ni based catalysts for carbon dioxide reforming of methane. These mesoporous catalysts performed high catalytic activity and long stability. Typically, the catalytic conversions of the CH4 and CO2 were greatly close to the equilibrium conversion and no deactivation was observed during the 100 h long lifetime test. The advantageous structural properties of ordered mesoporous alumina contributed to high dispersion of the Ni particles among the mesoporous framework, which further accounted for the good catalytic activity due to more "accessible" Ni active sites for the reactants. The "confinement effect" of the mesopores could effectively prevent the thermal sintering of the Ni nanoparticles to some extent, committed to its long-term catalytic stability. Besides, the mesoporous catalysts possessed enhanced ability to withstand coke, although not any modifiers had been added. Properties of the coke over the mesoporous catalyst were also carefully investigated. Therefore, the ordered mesoporous alumina was a promising catalyst support for the carbon dioxide reforming with methane. Copyright (C) 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
Aerosol metal-organic framework-derived Ni–Zn–Al hybrid catalyst for efficient methane Bi-reforming

Chuan-Bin Du,Jia-Yun Tu,Zhi Xuan Law,De-Hao Tsai

DOI: https://doi.org/10.1016/j.ijhydene.2024.01.097

IF: 7.2

2024-02-01

International Journal of Hydrogen Energy

Abstract:Bi-reforming of methane (BRM) has emerged as a promising advancement in hydrogen production via direct carbon utilization. To promote BRM, metal-organic framework (MOF)-derived Ni–ZnO–Al2O3 hybrid catalyst was developed via aerosol-assisted approach. The results demonstrated that the incorporation of Al2O3 nanoparticle cluster and ZnO with Ni alloy enhanced the catalytic activity. Superior conversions of reactants and operation stability of the MOF-derived Ni–ZnO–Al2O3 hybrid catalyst was observed, and a high turnover frequency (TOF CH4) of 2.86 s−1 at a moderate operating temperature (650 °C) was achieved. Further, the H2/CO ratio of 1.4–6.5 was attained through the proper adjustment of feed ratios (H2O/CH4, CO2/CH4) and reaction temperature (600–700 °C). Overall, the newly fabricated MOF-derived Ni–ZnO–Al2O3 hybrid catalyst via aerosol-assisted method, demonstrated significant improvements in reducing the required operating temperature of BRM, which is beneficial for simultaneous reduction of the CO2 generated from the methane reforming plus energy consumption, and advancing the development of low-carbon H2 production.

energy & fuels,electrochemistry,chemistry, physical
γ-Al 2 O 3 sacrificial template method for preparing flower-like Ni–Mg–Al catalysts for dry reforming of methane

Jing Zhang,Hui Fan,Yijie Wang,Rui Li,Qingxiang Ma,Tian-Sheng Zhao

DOI: https://doi.org/10.1016/j.ijhydene.2023.08.182

IF: 7.2

2023-09-02

International Journal of Hydrogen Energy

Abstract:A series of NiMgAl-X catalysts are prepared by adding the γ-Al 2 O 3 as a sacrificial template method through co-precipitation and applied to the dry reforming of methane (DRM). The catalysts were characterized by XRD, SEM, TEM, H 2 -TPR, CO 2 -TPD, Raman, TPH, and TG. The results show that the appropriate addition of γ-Al 2 O 3 can improve the structural stability of the catalyst so that the catalyst can maintain a well-shaped flower-like lamellar structure after calcination at 700 °C, improve the nickel dispersion and surface alkalinity to a certain extent, and improve its catalytic activity while maintaining good stability. The NMA-1 catalyst exhibits the highest catalytic activity of 73.7% and 83.2% conversion of CH 4 and CO 2 respectively after 50 h reaction, which is increased by 4.3% and 3.0% compared to the NMA catalyst.

energy & fuels,electrochemistry,chemistry, physical
Effect of Pore Structure on Ni/Al2O3 Microsphere Catalysts for Enhanced CO2 Methanation

Huilin Yi,Qiangqiang Xue,Shuliang Lu,Jiajia Wu,Yujun Wang,Guangsheng Luo

DOI: https://doi.org/10.1016/j.fuel.2022.123262

IF: 7.4

2022-01-01

Fuel

Abstract:An understanding of the support effect is fundamental for guiding the rational design of heterogeneous catalysts. Herein, the role of pore structure on metal dispersion and catalytic performance was comprehensively investigated using Ni/Al2O3 catalysts. Three different Al2O3 supports, including Al2O3 microspheres prepared in microchannels and two commercially available Al2O3 supports named Sample 1 and Sample 2, were used and the Ni/Al2O3 catalysts were prepared by wetness impregnation method. X-ray diffraction, transmission electron microscopy, H2 temperature-programmed reduction, X-ray photoelectron spectroscopy, N2 adsorption-desorption, and H2 pulse chemisorption analyses combined with a sintering kinetic model were used to investigate the effect of the support pore structure. The narrow pore size distribution (3-15 nm) of Al2O3 microspheres and Sample 1 led to a uniform NiO dispersion for the calcined catalysts. Moreover, the high specific surface area (291 m2/g) and large pore volume (1.0 mL/g) of the Al2O3 microspheres were beneficial for the deposition of NiO particles inside mesopore to obtain a stronger metal-support interaction. Owing to the smaller NiO nanoparticles and stronger metal-support interaction, the reduced Ni/Al2O3 microspheres exhibited an average Ni particle size of 10.2 nm under 36 wt% nickel loading, whereas the average Ni particle size loaded on Sample 1 and Sample 2 were 12.6 nm and 13.2 nm, respectively. The optimized CO2 conversion of 87.0% at 300 degrees C under atmospheric pressure was attributed to the large pore volume and uniform Ni dispersion of Ni/ Al2O3 microsphere catalysts while the same value for Sample 1 and Sample 2 catalysts was 81.5% and 55.0%, respectively. This work provides valuable guidelines for designing effective CO2 methanation support and proves the potential application of Al2O3 microspheres for CO2 methanation.
Promoted Nickel–Cobalt Bimetallic Catalysts for Biogas Reforming

Maryam Meshksar,Mohammad Reza Kiani,Alireza Mozafari,Mohammad Amin Makarem,Mohammad Reza Rahimpour

DOI: https://doi.org/10.1007/s11244-021-01532-y

IF: 2.781

2021-11-18

Topics in Catalysis

Abstract:The catalytic performance of Ni, Co, and Ni–Co-based catalysts on Al2O3 support are investigated in the dry methane reforming reaction. Besides, the influence of La or Y promoters on catalytic activity and structural properties of synthesized catalysts are examined in this paper. The prepared catalysts are characterized using N2 Adsorption/Desorption, FESEM, EDX, and XRD techniques. Higher average CH4 and CO2 conversions, as well as hydrogen yield, are obtained using Ni-Co catalyst with equal weight ratios. This could be the result of better dispersion of active sites according to the FESEM images and thus higher BET surface area of this catalyst compared with other un-promoted ones. Although the addition of La does not enhance the catalytic activity and structural properties of the 9Ni–9Co/Al2O3 sample, the presence of Y2O3 particles has a positive effect on both mentioned catalyst features. The maximum CH4 conversion of 99.39%, CO2 conversion of 92.38%, H2 yield of 86.20% and H2/CO molar ratio of 1.50 are achieved using 5Y–9Ni–9Co/Al2O3 at 700 °C. Besides, this catalyst shows lower deposited coke and higher stability compared with other promoted/un-promoted catalysts. The comparison between the activity of 5Y–9Ni–9Co/Al2O3 and industrial 18%Ni/Al2O3 during 11 h DRM shows that although 18%Ni/Al2O3 has higher conversions at first 9 h, its activity is decreased more than 5Y–9Ni–9Co/Al2O3 due to the coke deposition.

chemistry, physical, applied
Bi-reforming of Methane with Carbon Dioxide and Steam on Nickel-Supported Binary Mg–Al Metal Oxide Catalysts

Dedong He,Yimin Zhang,Zichun Wang,Yi Mei,Yijiao Jiang

DOI: https://doi.org/10.1021/acs.energyfuels.9b03312

2020-03-13

Abstract:Bi-reforming of methane (CH4) with carbon dioxide (CO2) and steam is a promising process to produce syngas with a H2/CO ratio of about 2, which can be directly used as a feedstock for methanol synthesis. This work studied nickel nanoparticles supported on the binary Mg–Al metal oxide catalysts for the bireforming of CH4. The XRD, TEM, and FT-IR results confirm the successful synthesis of Ni/MgO, Ni/MgxAlyO, and Ni/Al2O3 catalysts. The TPR profile shows that the reduction temperature of Ni species was slightly decreased upon addition of Al due to the formation of the NiAl2O4 phase. The XPS spectra demonstrate that Ni/MgO and Ni/Al2O3 exhibit higher amounts of Ni0 after H2 reduction. It can explain the origin of the superior catalytic performance of Ni/MgO and Ni/Al2O3 over the Ni/MgxAlyO catalysts possessing less Ni0 species during the H2 reduction process. Compared to the conventional dry reforming of CH4, the bi-reforming process features a higher CH4 conversion and a H2/CO ratio close to 2, which is suitable for methanol synthesis without further separation and adjustment steps.

energy & fuels,engineering, chemical
Ni-based Catalyst Supported on Ordered Mesoporous Al2O3 for Dry CH4 Reforming: Effect of the Pore Structure

Zhihao Zhou,Soomro Sarmad,Chao Huang,Guoshu Deng,Zhenkun Sun,Lunbo Duan

DOI: https://doi.org/10.1016/j.ijhydene.2023.04.334

IF: 7.2

2024-01-01

International Journal of Hydrogen Energy

Abstract:Ni-based catalysts supported on ordered mesoporous Al2O3 with 2-D hexagonal and 3-D cubic pore structures are synthesized via evaporationinduced self-assembly for catalyzing dry CH4 reforming to produce syngas. The Ni-Al2O3 catalysts with 3-D pore structure exhibit higher activity in terms of CH4 and CO2 conversions than those with 2-D pore symmetry, due to the better mass transfer of the 3-D interconnected pore structure for the accessibility of Ni0 active sites. And a higher Ni content slightly promotes catalytic activity, owing to more exposed active sites. However, a higher Ni content causes more severe carbon deposition during long-term reaction. During the long-term stability tests, the catalysts with 2.5 wt% Ni maintain the highest stability regardless of the pore structure, and the catalyst with 3-D pore structure is more advantageous to both activity and stability. Meanwhile, the catalyst with 2.5 wt% Ni and 3-D pore structure shows the lowest carbon deposition.(c) 2023 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Improved performance of Ni/Al2O3 catalyst deriving from the hydrotalcite precursor synthesized on Al2O3 support for dry reforming of methane

Yan Xu,Xihua Du,Liluo Shi,Teng Chen,Hongri Wan,Peng Wang,Shuai Wei,Bing Yao,Jie Zhu,Ming Song

DOI: https://doi.org/10.1016/j.ijhydene.2021.01.189

IF: 7.2

2021-04-01

International Journal of Hydrogen Energy

Abstract:Exploiting Ni-based catalysts with excellent catalytic activity and anti-coking ability is significant for dry reforming of CH4 with CO2 (DRM) which is a promising route to CO2 utilization. In this work, the Ni/Al2O3 catalyst with hydrotalcite precursor (NiAl-LDH) was synthesized by a facile in-situ growth method. And the effect of the NiAl-LDH structure on the catalytic activity and anti-coking ability of Ni/Al2O3 catalyst was revealed. The H2-temperature programmed desorption (H2-TPD) revealed that better Ni dispersion and more Ni–Al2O3 interface could be obtained by the NiAl-LDH precursor, which were vital for the activation of CH4 and CO2. Moreover, the NiAl-LDH precursor with non-LDH phase or turbostratic structure was also created by insufficient or extra amount of urea, and the obtained catalysts exhibited a poor catalytic stability, further confirming the importance of the LDH structure. In comparison with the Ni-IMP catalyst prepared by the conventional impregnation method, the CH4 conversion increased by 16% and the carbon deposition decreased by 75% over Ni-6 catalyst with well-organized LDH precursor under the same reaction conditions. Hence, this work represents an important step toward developing Ni-based catalysts with excellent catalytic activity and anti-coking ability for DRM with the LDH precursor.

energy & fuels,electrochemistry,chemistry, physical
Catalytic Methanation of Syngas over Ni-based Catalysts with Different Supports

Yincong Liu,Lingjun Zhu,Xiaoliu Wang,Shi Yin,Furong Leng,Fan Zhang,Haizhou Lin,Shurong Wang

DOI: https://doi.org/10.1016/j.cjche.2016.10.019

IF: 3.8

2017-01-01

Chinese Journal of Chemical Engineering

Abstract:Co-precipitation method was selected for the preparation of Ni/Al2O3, Ni/ZrO2 and Ni/CeO2 catalysts, and their performances in methanation were investigated in this study. The structure and surface properties of these catalysts were characterized by BET, XRD, H2-TPD, TEM and H2-TPR. The results showed that the catalytic activity at low temperature followed the order: Ni/Al2O3 > Ni/ZrO2 > Ni/CeO2. Ni/Al2O3 catalyst presented the best catalytic performance with the highest CH4 selectivity of 94.5%. The characterization results indicated that the dispersion of the active component Ni was the main factor affecting the catalytic activity and the one with higher dispersion gave better performance.
Porous Nickel‐Alumina Derived from Metal‐Organic Framework (MIL‐53): A New Approach to Achieve Active and Stable Catalysts in Methane Dry Reforming

Leila Karam,Julien Reboul,Sandra Casale,Pascale Massiani,Nissrine El Hassan

DOI: https://doi.org/10.1002/cctc.201901278

IF: 4.5

2019-11-14

ChemCatChem

Abstract:An Al‐containing MIL‐53 metal‐organic framework with very high surface area (SBET=1130 m2.g−1, N2 sorption) was used as sacrificial template to prepare a nickel‐alumina‐based catalyst (Ni0AlMIL) highly active and stable in the reaction of dry reforming of methane (DRM). The procedure consisted in impregnating the activated (solvent free) MIL‐53 sample with a nickel precursor solution, then calcining the material to remove the organic linkers and subsequently reducing it to form the reduced nickel active phase. At the step of calcination, this procedure results in the formation of a porous uniform spinel phase with Ni nanospecies embedded in the alumina‐based matrix, as deduced from XRD, TPR and TEM analyses. This leads after reduction to a porous lamellar γ‐Al2O3 material with small Ni0 nanoparticles homogeneously dispersed and stabilized within the support. The performances of this catalyst in DRM are better than those of two reference Ni/alumina catalysts prepared for comparison by conventional nickel impregnation of two preformed alumina supports: a first one obtained by calcination of MIL‐53 (AlMIL) and a second one consisting of a commercial γ‐Al2O3 batch (AlCOM). Under steady state conditions at a temperature of 650 °C and a pressure of 1 bar, the higher CH4 and CO2 conversions (till 3 times higher than on Ni0/AlCOM), high catalytic stability (no loss of activity after 13–100 h) and higher selectivity towards DRM (H2:CO products ratio remaining at 1) on Ni0AlMIL compared to the other catalysts is believed to come from the particularly strong interaction between the nickel and alumina phases generated by using the unique high specific surface of the parent MOF support to deposit nickel. This creates an intimate mixing favorable to a persisting interaction of the nickel nanoparticles with the alumina support in the reduced material. The lamellar shape of the γ‐Al2O3 composing the catalyst and its remaining high specific surface may also contribute to the excellent Ni resistance to sintering and in turn to the inhibition of carbon nanotubes formation during the reaction.

chemistry, physical
Rational design of nickel-based catalyst coupling with combined methane reforming to steadily produce syngas

Qinhong Wei,Xinhua Gao,Luhui Wang,Qingxiang Ma

DOI: https://doi.org/10.1016/j.fuel.2020.117631

IF: 7.4

2020-07-01

Fuel

Abstract:Inhibiting the aggregation of Ni particles and coke deposition on supported nickel catalysts has always been an enormous challenge in methane reforming to syngas. To address the problem, in this study, a Ce-Al-O supported Ni mesoporous catalyst (Ni/Ce-Al-O-A) was designed and synthesized by using evaporation-induced self-assembly (EISA) method and citric acid auto-reduction (AR) method, respectively. The prepared Ni/Ce-Al-O-A catalyst, without further reduction, was used for combined methane dry reforming comprising CO2 dry reforming of methane (DRM) and methane partial oxidation (MPO) to effectively produce syngas. Employing citric acid auto-reduction method for catalyst preparation directly led to the formation of metallic Ni by calcining the precursor of Ni/Ce-Al-O-A in argon atmosphere, with high dispersion and small particle size (at around 4.5 nm) of metallic Ni being obtained. The Ni/Ce-Al-O-A catalyst presented high catalytic activity, better than those of reference catalyst prepared by general impregnation method and the commercial alumina supported Ni catalyst synthesized by citric acid auto-reduction method. In a 250 h lifetime test, the Ni/Ce-Al-O-A catalyst exhibited an extremely catalytic stability and anti-coking ability, and no deactivation was observed. The excellent catalytic activity of Ni/Ce-Al-O-A catalyst was mainly attributed to the Ce-incorporated Ce-Al-O that facilitated the adsorption and activation of CO2 as well as the combined methane reforming (DRM-MPO) in which the existing oxygen could effectively inhibit the coke formation.

energy & fuels,engineering, chemical
Nickel based catalysts supported on porous support for methane steam reforming: potential and short review

M H A Seman,N H Othman,N Osman,A M M Jani

DOI: https://doi.org/10.1088/1755-1315/1151/1/012061

2023-03-29

IOP Conference Series: Earth and Environmental Science

Abstract:The world is now demanding other sustainable energy that can help explore new technologies, especially energy conversion and storage. Hydrogen is regarded as one of the most promising oils and gas successors as a fuel due to its high energy content per unit mass and it burns completely free of pollutants. A widely used method for hydrogen production is steam reforming methane (SRM) from biogas. In the SRM process, using a catalyst is crucial, and, if compared to the available metal-based catalysts, Ni-based catalysts provide an acceptable high activity and a lower cost. In addition, the support material of a catalyst significantly affects its stability, especially for catalysts exposed to elevated temperatures. In this work, porous alumina support was used as a support material for the preparation of a nickel-based catalytic hollow membrane reactor. Porous alumina support was fabricated using a double-step anodization method. The presence of large pores (≈120 nm) on support material contributes to decreasing the resistance to mass transfer. The study also highlights the recent progress on methane steam reforming reaction, giving a short overview of catalyst utilization and the fundamentals of SRM through the developed membrane reactor.

English Else
Improving Catalytic Stability and Coke Resistance of Ni/Al2O3 Catalysts with Ce Promoter for Relatively Low Temperature Dry Reforming of Methane Reaction

He Lulu,Chen Xin,Ren Yuanhang,Yue Bin,Tsang Shik Chi Edman,He Heyong

DOI: https://doi.org/10.1007/s40242-021-1281-5

IF: 3.1

2021-01-01

Chemical Research in Chinese Universities

Abstract:A series of Ni catalysts supported on alumina with different Ce contents(1.0%–6.0%, mass fraction) was prepared by the impregnation method and used for dry reforming of methane(DRM) at a relatively low temperature of 650 °C. The promotion effect of Ce with different loading amounts on the physicochemical properties of the catalysts was systematically characterized by transmission electron microscopy(TEM), X-ray diffraction(XRD), N2 adsorption-desorption, thermo elemental IRIS Intrepid inductively coupled plasma atomic emission spectrometer (ICP-AES), UV-visible diffuse reflectance spectroscopy(UV-Vis DRS), Fourier transformation infrared(FTIR) spectra, H2-temperature programmed reduction(H2-TPR) analysis, H2-temperature programmed desorption(H2-TPD), and The X-ray photoelectron spectroscopy(XPS) techniques. The results indicate that all the catalysts mainly exist in the NiAl2O4 phase after being calcined at 750 °C with small Ni particle sizes due to the strong metal-support interaction derived from the reduction of the NiAl2O4 phase. The Ce-promoted catalysts show better catalytic performance as well as the resistance against sintering of Ni particles and deposition of carbon compared to the Ni/Al2O3 catalyst. The Ni-6Ce/Al2O3 exhibits the best catalytic stability and coke resistance among the four catalysts studied, which is due to its small Ni nanoparticles sizes, excellent reducibility as well as high amount of active oxygen species. In a 400 h stability test for DRM reaction at 650 °C, Ni-6Ce/Al2O3 exhibits less coke deposition and small growth of Ni nanoparticles. This work provides a simple way to preparing the Ni-Ce/Al2O3 catalyst with enhanced catalytic performance in DRM. The Ni-6Ce/Al2O3 catalyst has great potential for industrial application due to its anti-sintering ability and resistance to carbon deposition.
Highly Stable Ni−B/Honeycomb−Structural Al2O3 Catalysts for Dry Reforming of Methane

Yuhao Luo,Tongming Su,Liuyun Chen,Hongbing Ji,Zuzeng Qin

DOI: https://doi.org/10.1002/asia.202400700

2024-07-29

Chemistry - An Asian Journal

Abstract:Two−component catalysts have garnered significant attention in the field of catalysis due to their ability to inhibit Ni sintering. In the present work, honeycomb−structured Al2O3−supported Ni and B were prepared to enhance coke tolerance during dry reforming of methane (DRM). Transmission electron microscopy (TEM) revealed that the average particle sizes on Ni/Al2O3 and Ni−0.16B/Al2O3 were 7.6 nm and 4.2 nm, respectively, indicating that B can effectively inhibit Ni sintering. After a 100‐hour reaction, the conversion of CH4 and CO2 on Ni/Al2O3 decreased by approximately 5%, whereas on Ni−0.16B/Al2O3, there was no significant decrease in CH4 and CO2 conversion, with values of approximately 81.6% and 87.2%, respectively. In situ DRIFT spectra demonstrated that Ni−0.16B/Al2O3 enhanced the activation of CO2, thus improving the catalyst's stability. A Langmuir−Hinshelwood−Hougen−Watson (LHHW) model was developed for intrinsic kinetics, and the resulting kinetic expressions were well fit to the experimental data, with R2 values exceeding 0.9. The activation energies were also calculated. The outstanding stability of Ni−0.16B/Al2O3 can be attributed to its stable honeycomb structure and B's ability to significantly inhibit Ni sintering, reduce catalyst particle size, and enhance coke tolerance.

chemistry, multidisciplinary
Biogas Reforming on Hydrotalcite-Derived Ni-Mg-Al Catalysts: the Effect of Ni Loading and Ce Promotion

Dori Yosef Kalai,Kristian Stangeland,Wakshum M. Tucho,Yiying Jin,Zhixin Yu

DOI: https://doi.org/10.1016/j.jcou.2019.05.011

IF: 7.7

2019-01-01

Journal of CO2 Utilization

Abstract:Due to the expected large growth of biogas production, particularly in Europe, biogas utilization technology could play an important role in the near future. Direct biogas reforming through dry reforming of methane (DRM) has great potential as an intermediate step in biogas upgrading to fuels and commodity chemicals. In this work, a series of Ce-promoted Ni-Mg-Al hydrotalcite (HT) derived catalysts with different Ni loadings was prepared to study their applicability for model biogas reforming at low CO2 concentrations. The catalysts were characterized by N-2 physisorption, X-ray diffraction (XRD), temperature-programmed reduction (TPR), H-2-chemisorption, thermogravimetric analysis (TGA) and transmission electron microscopy (TEM). Reforming of model biogas was carried out at 600 degrees C, 1 bar and non-diluted CO2/CH4 = 1:3 and high GHSV. To further assess the effect of Ni loading on the Ce-promoted catalysts, DRM was studied in a temperature range of 500-800 degrees C. Furthermore, comprehensive post-mortem characterizations were conducted to elucidate the consequence of carbon formation and Ni sintering on the catalytic activity and stability. It was demonstrated that higher Ce/Ni ratio results in more active catalyst, which is also more resistant to sintering and coke deposition even at low concentrations of CO2 in the feed.

A blind comparison of the effectiveness of endoscopic ultrasonography and endoscopy in staging early gastric cancer.

Effect of support texture properties on Ni-Fe/γ-Al_2O_3 catalyst structure and catalytic performance for CO methanation

Metal-Organic Framework-Templated Synthesis of Nickel-Alumina Nanocatalysts Improves Catalyst-Support Interaction for Higher Activity and Stability in Biogas Reforming under Controlled Oxidizing Conditions

Effect of Modified Alumina Support on the Performance of Ni-Based Catalysts for CO2 Reforming of Methane

Facile Route for Synthesizing Ordered Mesoporous Ni–Ce–Al Oxide Materials and Their Catalytic Performance for Methane Dry Reforming to Hydrogen and Syngas

One‐pot Synthesis of Ordered Mesoporous NiCeAl Oxide Catalysts and a Study of Their Performance in Methane Dry Reforming

Ordered Mesoporous Alumina Supported Nickel Based Catalysts for Carbon Dioxide Reforming of Methane

Aerosol metal-organic framework-derived Ni–Zn–Al hybrid catalyst for efficient methane Bi-reforming

γ-Al 2 O 3 sacrificial template method for preparing flower-like Ni–Mg–Al catalysts for dry reforming of methane

Effect of Pore Structure on Ni/Al2O3 Microsphere Catalysts for Enhanced CO2 Methanation

Promoted Nickel–Cobalt Bimetallic Catalysts for Biogas Reforming

Bi-reforming of Methane with Carbon Dioxide and Steam on Nickel-Supported Binary Mg–Al Metal Oxide Catalysts

Ni-based Catalyst Supported on Ordered Mesoporous Al2O3 for Dry CH4 Reforming: Effect of the Pore Structure

Improved performance of Ni/Al2O3 catalyst deriving from the hydrotalcite precursor synthesized on Al2O3 support for dry reforming of methane

Catalytic Methanation of Syngas over Ni-based Catalysts with Different Supports

Porous Nickel‐Alumina Derived from Metal‐Organic Framework (MIL‐53): A New Approach to Achieve Active and Stable Catalysts in Methane Dry Reforming

Rational design of nickel-based catalyst coupling with combined methane reforming to steadily produce syngas

Nickel based catalysts supported on porous support for methane steam reforming: potential and short review

Improving Catalytic Stability and Coke Resistance of Ni/Al2O3 Catalysts with Ce Promoter for Relatively Low Temperature Dry Reforming of Methane Reaction

Highly Stable Ni−B/Honeycomb−Structural Al2O3 Catalysts for Dry Reforming of Methane

Biogas Reforming on Hydrotalcite-Derived Ni-Mg-Al Catalysts: the Effect of Ni Loading and Ce Promotion