Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. This paper investigates the correlation between the surface quality and the cross-sectional quality, microstructure, internal defects, and mechanical properties of specimens formed by selective laser melting (SLM) under different scanning speeds and scanning intervals. Therefore, different machining parameters were chosen to prepare titanium alloy specimens by SLM technique. The surface morphology of the specimens was characterized using a light microscope, and the surface quality, microstructure, internal defects, and deep connection of the mechanical properties of the specimens formed under different parameters were investigated. In addition, numerical simulation of the melt pool morphology under different scanning speeds was used. The results show that there is a strong correlation between the surface quality of the specimen and the section quality and mechanical properties. When the scanning speed is 350 mm/s, the surface roughness is 14.7 μm, the density is 99.99%, the tensile strength and yield strength are 1209 and 1151 Mpa respectively, and the surface quality, cross-sectional quality and mechanical properties all tend to deteriorate as the scanning speed increases. When the scanning interval is 0.11 mm, the mechanical properties of surface quality and cross-sectional quality are optimal, the surface roughness is 14.5 μm, and the density reaches 99.99%, at this time, the microscopic needle martensite α′ phase is uniformly distributed and refined, and its mechanical properties are optimal, the tensile strength is 1239 MPa, and the internal hole defects are less. Numerical simulations of a single track melt pool show that the depth of depression caused by the recoil pressure is larger and the melt pool is deeper when the scanning speed is 350 mm/s. Therefore, it has better fluidity and ductility. Simulation results of the double tracks show that when the scanning interval is 130 μm, a large amount of incompletely melted powder at the midline of the double track does not lap well, which leads to the formation of pore defects inside the specimen. The above simulation results are highly consistent with the surface quality of the specimens during the experiments, which provides a guide to analyze the connection between the melt pool evolution and the Ti6Al4V molding quality.

Effects of machining surface and laser beam scanning strategy on machinability of selective laser melted Ti6Al4V alloy in milling

Effect of material anisotropy on ultra-precision machining of Ti-6Al-4V alloy fabricated by selective laser melting

Serrated chip characteristics and formation mechanism in high-speed machining of selective laser melted Ti6Al4V alloys

Study on the mechanism of correlation between surface quality and tissue properties of Ti6Al4V alloy formed by selective laser melting

Effect of Scanning Strategies on the Microstructure and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated through Selective Laser Melting

Study on machinability characteristics of novel additive manufactured titanium alloy (Ti-6Al-4V) fabricated by direct metal laser sintering

The effect of a remelting treatment scanning strategy on the surface morphology, defect reduction mechanism, and mechanical properties of a selective laser-melted Al-based alloy

Effects of laser power on the microstructural evolution of novel Ti–6Zr–5Fe alloy fabricated by selective laser melting

Experimental Investigation of the Micro-Milling of Additively Manufactured Titanium Alloys: Selective Laser Melting and Wrought Ti6Al4V

Comparative study on machinability and surface integrity of γ-TiAl alloy in laser assisted milling

Top surface roughness evolution during selective laser melting of AlCu5MnCdVA aluminum alloy

Difference-extent of microstructure and mechanical properties: Simulating multi-laser selective melting Ti6Al4V

3D surface topography analysis and functionality-related performance of the machined surface in slot micro-milling titanium alloy Ti6Al4V

Effect of laser rescanning on Ti6Al4V microstructure during selective laser melting

Effect of Overlapping Remelting on Microstructures and Mechanical Properties of Selective Laser‐Melted Ti‐6Al‐4V Alloy

Effect of scanning strategies on the microstructure and mechanical properties of Ti–15Mo alloy fabricated by selective laser melting

Role of laser remelting and heat treatment in mechanical and tribological properties of selective laser melted Ti6Al4V alloy

On influence of microstructural anisotropy of additive manufactured structures upon machining dynamics: An example of milling of Ti6Al4V thin-walled parts

Simulation and experimental study of the hole-making process of Ti-6Al-4V titanium alloy for selective laser melting

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Effects of laser polishing on surface morphology and mechanical properties of additive manufactured TiAl components