Abstract:At mesoscale, the blade of micro impeller with Ti-6Al-4V titanium alloy (micro thin wall with mixed boundaries) is a thin-walled structure, characterized by small size, low stiffness, high surface precision, complex boundaries, and difficult-to-control machining deformation. To control and reduce the deformation of micro thin wall, it is necessary to study the micro-deformation mechanisms during milling micro thin-wall parts. In side milling of micro thin wall with mixed boundaries, the micro thin wall suffers from dynamic alternating forces, and the deformation modes are complex, so the direct and accurate theoretical modelling is difficult to make. Since the feed speed in milling micro thin wall is less, the small deformation of micro thin wall can be described based on the flexure deformation model of the thin plate subjected to elastic loadings. Firstly, accompanied by the reciprocal theorem of work for a curved thin plate, Kirchhoff-Love small deformation model of micro thin wall is used to establish the deformation equation and boundary conditions of micro thin wall with mixed boundaries under concentrated milling forces. Thus, the obtained boundary conditions are mainly applied to the subsequent finite element simulation of three-dimensional milling deformation of micro thin wall. Then a three-dimensional deformation simulation of the micro thin wall under different milling parameters is carried out by considering the micro-walled structure, material elasto-plastic constitutive model, the stiffness and geometric structure of micro milling tools in finite element method. In the workpiece constitutive modelling, considering the strain gradient plastic model in micro milling of Ti-6Al-4V titanium alloy, the workpiece plastic constitutive model is modified by introducing the intrinsic characteristic length of the material to describe the size effects in mesoscale micro milling. Finally, a series of the corresponding experiments on the milling of titanium alloy micro thin walls are carried out. By comparing and analyzing the experimental values and finite element numerical results of the micro thin-walled deformation, the micro deformation mechanisms in milling of thin wall are revealed. It also verifies the accuracy and effectiveness of this established milling finite element model of thin wall, and provides theoretical basis and technical support for controlling the milling deformation of micro thin-walled parts.

On influence of microstructural anisotropy of additive manufactured structures upon machining dynamics: An example of milling of Ti6Al4V thin-walled parts

The Mechanism of Anisotropic Micro-Milling Properties in Additively Manufactured Ti-6Al-4V Alloy

Microstructure and Anisotropic Mechanical Properties of Selective Laser Melted Ti6Al4V Alloy under Different Scanning Strategies

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Effect of Material Microstructure on Tool Wear Behavior During Machining Additively Manufactured Ti6Al4V

Effect of material anisotropy on ultra-precision machining of Ti-6Al-4V alloy fabricated by selective laser melting

Dynamic Mechanical Properties and Machinability Characteristics of Selective Laser Melted and Forged Ti6Al4V

Microstructure Evolution of Ti-6Al-2Zr-1Mo-1V Alloy and Its Mechanism in Multi-Pass Flow Forming

Effects of machining surface and laser beam scanning strategy on machinability of selective laser melted Ti6Al4V alloy in milling

Microstructure- and Cooling/lubrication Environment-Dependent Machining Responses in Side Milling of Direct Metal Laser-Sintered and Rolled Ti6Al4V Alloys

Deformations of Ti-6Al-4V additive-manufacturing-induced isotropic and anisotropic columnar structures: Insitu measurements and underlying mechanisms

Machining of Thin-walled Parts Produced by Additive Manufacturing Technologies

Experimental Investigation of the Micro-Milling of Additively Manufactured Titanium Alloys: Selective Laser Melting and Wrought Ti6Al4V

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability

Simulation-assisted Investigation on the Formation of Layer Bands and the Microstructural Evolution in Directed Energy Deposition of Ti6Al4V Blocks

Microstructure evolution characterization of Ti 2 AlNb intermetallic alloys subjected to side milling

Mechanical Behavior of Additive Manufacturing (AM) and Wrought Ti6Al4V with a Martensitic Microstructure

Heterogeneous microstructure evolution in Ti-6Al-4V alloy thin-wall components deposited by plasma arc additive manufacturing

Multiple Α Sub-Variants and Anisotropic Mechanical Properties of an Additively-Manufactured Ti-6Al-4V Alloy

Research on Deformation Law and Mechanism for Milling Micro Thin Wall with Mixed Boundaries of Titanium Alloy in Mesoscale

The State of the Art in Machining Additively Manufactured Titanium Alloy Ti-6Al-4V