Abstract:Thin-walled parts are often used in various industrial applications and due to their functional requirements, higher accuracies are generally desired. But due to their low stiffness characteristics, deformation and chatter problems are frequently encountered in their machining, thus resulting in poor accuracy. Moreover, due to 5-axes milling, which is usually required for finish machining of such parts, further complexities in the process are added and, consequently, achieving higher accuracy becomes more challenging. Therefore, in this study, the influence of tool inclination angle and feeding direction has been investigated on the resultant surface accuracy of thin cantilever shaped parts in finish milling conditions through experiments, finite element method simulations and theoretical discussions. Moreover, since work material’s microstructure and hardness also have key influence on its machinability, therefore, the effect of heat treatment state on resulting surface accuracy also has been explored. Three different titanium alloy, Ti–6Al–4 V specimens have been used. Two of the specimens were given solution treatment at 1050 ℃/1 h followed by aging at 550 ℃/4 h. One of the specimens after being solution treated was allowed to cool in air while the other was cooled in water to obtain different microstructure and hardness whereas the third specimen was used in as-received condition (casted). The three Ti–6Al–4 V specimens were machined at five different tool inclination angles (60°, 70°, 75°, 80°, and 85°) with two feeding directions (horizontal inwards and vertical inwards). Results have shown that the angle near the perpendicular to the surface i.e. 85° (5° away from the perpendicular) has lowest deformation value and also has better surface quality, which shows that the lowest effective cutting speed at this angle has helped in achieving higher accuracy. Moreover, among the cutting directions studied, vertical inward direction produces smoother surface due to its less pushing effect on the surface being cut as compared to horizontal inwards direction. And in terms of heat treatment state, the specimen which was cooled in air after being solution treated has produced better results for all cutting conditions studied, mainly attributed to fine homogenous lamellar α + β Ti–6Al–4 V structure achieved due to slow cooling rate of air. Analysis of variance using response surface methodology has been carried out to develop predictive model and to study the influence of each variable on the accuracy. The developed model has shown good accuracy when validated through additional experiments.

Machining of Thin-walled Parts Produced by Additive Manufacturing Technologies

Fabrication of Electron Beam Melted Titanium Aluminide: The Effects of Machining Parameters and Heat Treatment on Surface Roughness and Hardness

On influence of microstructural anisotropy of additive manufactured structures upon machining dynamics: An example of milling of Ti6Al4V thin-walled parts

Comparative study on micro-milling machinability of titanium alloys prepared by different processes: Forging process, additive manufacturing process and heat-treatment process

Overview of Machinability of Titanium Alloy (Ti6Al4V) and Selection of Machining Parameters

The State of the Art in Machining Additively Manufactured Titanium Alloy Ti-6Al-4V

Microstructure and Mechanical Properties of Ti-6Al-4V Additively Manufactured by Electron Beam Melting with 3D Part Nesting and Powder Reuse Influences

Energy saving in milling of electron beam–melted Ti6Al4V parts: influence of process parameters

Microstructure and Mechanical Properties of Titanium Alloys Produced by Additive Technologies: New Approaches and Promising Areas of Research

Energy consumption assessment in manufacturing Ti6Al4V electron beam melted parts post-processed by machining

Additive Manufacturing of Titanium Alloys by Electron Beam Melting: A Review

Evaluation of thermal and geometric properties of martensitic stainless steel thin walls built by additive manufacturing cold metal transfer (CMT) processes

Effect of Material Microstructure on Tool Wear Behavior During Machining Additively Manufactured Ti6Al4V

Influence of Tools and Cutting Strategy on Milling Conditions and Quality of Horizontal Thin-Wall Structures of Titanium Alloy Ti6Al4V

Experimental Investigation of the Micro-Milling of Additively Manufactured Titanium Alloys: Selective Laser Melting and Wrought Ti6Al4V

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

Influence of Tool Inclination Angle and Cutting Direction on Long Thin-Walled Part’s Dimensional and Geometric Accuracy when High-Speed Ball End Milling the Heat-Treated Titanium Alloy Ti–6Al–4 V

Study on machinability characteristics of novel additive manufactured titanium alloy (Ti-6Al-4V) fabricated by direct metal laser sintering

Machining Finish of Titanium Alloy Prepared by Additive Manufacturing

Effect of Hot Isostatic Pressing and Solution Heat Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Manufactured by Selective Laser Melting

Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing