Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

Comparative study on micro-milling machinability of titanium alloys prepared by different processes: Forging process, additive manufacturing process and heat-treatment process

Influence of Microstructure and Hardness on Machinability of Heat-Treated Titanium Alloy Ti-6Al-4V in End Milling with Polycrystalline Diamond Tools

Experimental Investigation of the Micro-Milling of Additively Manufactured Titanium Alloys: Selective Laser Melting and Wrought Ti6Al4V

Micromechanical Behaviour of TA15 Alloy Cylindrical Parts Processed by Multi-Pass Flow Forming

Effect of Material Microstructure on Tool Wear Behavior During Machining Additively Manufactured Ti6Al4V

Fabrication of Electron Beam Melted Titanium Aluminide: The Effects of Machining Parameters and Heat Treatment on Surface Roughness and Hardness

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

Investigation on surface quality in micro milling of additive manufactured Ti6Al4V titanium alloy

Finite Element Simulation and Experimental Research on Micro-Milling Process of Titanium Alloy

Numerical Simulation-Based Study on the Microstructure of TC4 Titanium Alloy in CMT Additive Manufacturing

Machinability of TiC-reinforced titanium matrix composites fabricated by additive manufacturing

Improvement of Microstructure and Mechanical Properties of TC4 Titanium Alloy GTAW based Wire Arc Additive Manufacturing by using Interpass Milling

Comparison of the Machinability of Titanium Alloy Forging and Powder Metallurgy Materials

Study of Different Micro Milling Blades on Milling Titanium Alloy TC4

Experimental Study on Cutting Force and Surface Integrity of TC4 Titanium Alloy with Longitudinal Ultrasonic-Assisted Milling

Investigation of Chip Formation Mechanism and Surface Integrity in High Speed Milling Titanium Alloy

Machining Finish of Titanium Alloy Prepared by Additive Manufacturing

Dynamic Mechanical Properties and Machinability Characteristics of Selective Laser Melted and Forged Ti6Al4V

Experimental Investigation on Machinability of α/β Titanium Alloys with Different Microstructures

Influence of Heat Treatments on Microstructure and Mechanical Properties of Laser Additive Manufacturing Ti-5Al-2Sn-2Zr-4Mo-4Cr Titanium Alloy

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy