Abstract:In this paper, Ni/Au/Ge/Ni/Au laminated metals were deposited on the n-(Al0.27Ga0.73)(0.5)In0.5P by electron beam evaporation, the ohmic contact with low contact resistance was successfully prepared by optimized annealing process. The specific contact resistance reached 1.4 x 10(-4) Omega.cm(2) when annealed at 445 degrees C for 600 s. The result of the secondary ion mass spectrometer shows that the solid-state reaction takes place at the interface between the laminated metal Ni/Au/Ge/Ni/Au and n-AlGaInP, then the germanium atoms and indium atoms diffuse outwards due to thermal decomposition and leave vacancies in the lattice. In this paper, the reason for the formation of ohmic contact is attributed to the fact that the germanium vacancy and indium vacancy are occupied by gallium atoms as donors to increasing the N-type doping concentration. The optimized annealing process can improve the ohmic contact performance of n-(Al0.27Ga0.73)(0.5)In0.5P with low doping concentration, but the specific contact resistivity has no obvious relationship with the annealing process when the of doping concentration of n-(Al0.27Ga0.73)(0.5)In0.5P increased. The Schottky barrier is high at low doping concentration of n-(Al0.27Ga0.73)(0.5)In0.5P. So inter diffusion in the annealing process could significantly increase the doping concentration of n-(Al0.27Ga0.73)(0.5)In0.5P and reduce the Schottky barrier height. Nevertheless, the Schottky barrier of the sample with high doping concentration is low enough what is not sensitive with inter diffusion. It provides a new method for the preparation of N-electrode of AlGaInP thin film light-emitting-diodes chip, as so as avoid the problem of n(+)-GaAs absorption in the conventional N-electrode preparation method and the problem of electrode dropping. However, there are still some shortcomings in this paper. The disadvantage is that the high doping concentration of n-AlGaInP will affect the crystal quality, which will reduce the luminous efficiency of LED. Therefore, in order to prepare ohmic contact with excellent properties on n-AlGaInP with lower doping concentration, optimizing the electrode design and the surface treatment of semiconductor materials are the keys to follow-up research.

Improving Gold and Palladium Ohmic Contacts of Carbyne-Based Devices

Study of bonding parameters with Al and Au wires on Pd and Ag coatings

Improving Graphene-metal Contacts: Thermal Induced Polishing

Improving contact of CNT - metal by annealing

Pd/Ge/Ti/Pt/Au Metal Stack on Semi-Insulating Gallium Arsenide: Ohmic Contact and Temperature Dependence

Reducing Contact Resistance in Graphene Devices through Contact Area Patterning

Annealing Nano-to-micro Contacts for Improved Contact Resistance

Improving Charge Injection at Gold/Conjugated Polymer Contacts by Polymer Insulator-Assisted Annealing for Transistors.

Contact Resistance Study of Various Metal Electrodes with CVD Graphene

Thermal stability investigation for Ohmic contact properties of Pt, Au, and Pd electrodes on the same hydrogen-terminated diamond

Searching for Device Processing Compatible Ohmic Contacts to Implanted P-Type 4H-Sic

Palladium Ohmic Contact on Hydrogen-Terminated Single Crystal Diamond Film

Thermal Annealing Effects on Ni/Au Contacts to P Type Gan in Different Ambient

Effect of Annealing Ambient on the Thermal Stability of Cu/Zr42si9n49/Si Contact System

Electronically transparent Ag-C(sp3) contacts result in low conductance junctions

Effects of Rapid Thermal Annealing on the Contact of Tungsten/p-Diamond

Experimental Research on Thermal Transport Properties of Crystallized Palladium-Based Alloys

Very low resistance Au/Ge/Ni/Ag based Ohmic contact formation to Al0.25/Ga0.75As/GaAs and Al0.48In0.52As/Ga0.47In0.53As heterostructures: A behavioral comparison

Study on the effect of thermal annealing process on ohmic contact performance of AuGeNi/n-AlGaInP

Gas Sensing Performance of Graphene-Metal Contact after Thermal Annealing

Resistance to Electrical Corrosion of Au-Cu Alloy Coatings for Electronic Contacts