Abstract:Background: A power injector is typically employed to deliver a contrast agent to a subject (e.g., humans, animals, phantoms) during MRI, but it is costly and cannot inject more than one subject at a time. Conventional syringe pumps housing multiple syringes are typically non-MRI compatible and, thus, should be placed outside the MRI room. Purpose: To develop the prototype of a cost-effective, easy-to-use, reliable syringe pump that could be deployed inside a clinical MRI bore and operated on during a scan. Methods: The MRI-compatible syringe pump (MSP) was designed using Solidworks 3D modeling software and fabricated using a Raise3D Pro2 Printer. The MSP was designed to infuse up to three syringes simultaneously. The injection speed was mainly controlled with different gear sets in the escapement unit and further adjusted by changing the effective hairspring length via a pinch pin. The MSP was evaluated with three gear sets (gear ratios: 0.20:1, 0.56:1, and 1.09:1) and 10 different effective hairspring lengths at each gear ratio. A video was recorded while operating MSP at each injection speed to calculate the volume injection rate of a 5-mL syringe (mL/s). The MSP was operated five times repeatedly at each injection speed, and the mean and standard deviation of the volume injection rate were calculated. Results: The volume injection rates produced by three gear ratios (0.20:1, 0.56:1, and 1.09:1) were 0.209 ± 0.003 mL/s, 0.411 ± 0.002 mL/s, and 0.625 ± 0.006 mL/s, respectively, at the full hairspring length. The injection rates of gear set 1 (gear ratio: 0.20:1) decreased from 0.273 ± 0.001 mL/s to 0.245 ± 0.001 mL/s with a decrement of 0.003 mL/s for 10 different effective hairspring lengths (r = 0.997, p < 0.001). The injection rates of gear set 2 (gear ratio: 0.56:1) decreased from 0.519 ± 0.003 mL/s to 0.469 ± 0.003 mL/s with a decrement of 0.006 mL/s (r = 0.987, p < 0.001), and that of gear set 3 (gear ratio: 1.09:1) decreased from 0.779 ± 0.012 mL/s to 0.709 ± 0.005 mL/s with a decrement of 0.007 mL/s (r = 0.963, p < 0.001). The coefficient of variation in the injection rate measurement was 0.727 ± 0.346%. Conclusions: The MSP is a portable device that can reliably deliver a liquid agent to multiple subjects inside a clinical MRI bore during a scan.

[Design and Realization of Contrast Medium Biphasic Hyperbaric Injector]

Research on dose and depth adjustable needle-free injector

Liquid difference reflux type injection pump

Design and manufacture a syringe pump for intelligent injection of specific doses of contrast medicine in medical imaging applications

Flow Stabilizer on a Syringe Tip for Hand-Powered Microfluidic Sample Injection

Technical note: 3D-printed MRI-compatible syringe pump

Design of an Intelligent Insulin Injector

A Novel Subcutaneous Infusion Delivery System Based on Osmotic Pump: in Vitro and in Vivo Evaluation.

Mechanistic Analysis of Solid–liquid Flow During Injection

Beam dynamic design of a high intensity injector for proton linac

High-precision, pressure-driven pump for sub-picoliter scale quantitative injection

Iodinated contrast injection data from a new technology

Conceptual design of linear injector for SSC of HIRFL

Conceptual design of injection system for Hefei Light source (HLS) upgrade project

Successful High Power Acceleration of the HSC Type Injector for Cancer Therapy in IMP

Flushing effect of micro-bolus pulse injection and its potential impact on peripheral veins under hemostasis

A Compact High-Average Current Photo-Injector

Liquid-Driven Microinjection System for Precise Fundus Injection

Design of A Portable Insulin Syringe Based on Msp430 Mcu

Conceptual Design of Hefei Advanced Light Source (hals) Injection System

A Digital Miniature Pump for Medical Applications