Abstract:Background: A power injector is typically employed to deliver a contrast agent to a subject (e.g., humans, animals, phantoms) during MRI, but it is costly and cannot inject more than one subject at a time. Conventional syringe pumps housing multiple syringes are typically non-MRI compatible and, thus, should be placed outside the MRI room. Purpose: To develop the prototype of a cost-effective, easy-to-use, reliable syringe pump that could be deployed inside a clinical MRI bore and operated on during a scan. Methods: The MRI-compatible syringe pump (MSP) was designed using Solidworks 3D modeling software and fabricated using a Raise3D Pro2 Printer. The MSP was designed to infuse up to three syringes simultaneously. The injection speed was mainly controlled with different gear sets in the escapement unit and further adjusted by changing the effective hairspring length via a pinch pin. The MSP was evaluated with three gear sets (gear ratios: 0.20:1, 0.56:1, and 1.09:1) and 10 different effective hairspring lengths at each gear ratio. A video was recorded while operating MSP at each injection speed to calculate the volume injection rate of a 5-mL syringe (mL/s). The MSP was operated five times repeatedly at each injection speed, and the mean and standard deviation of the volume injection rate were calculated. Results: The volume injection rates produced by three gear ratios (0.20:1, 0.56:1, and 1.09:1) were 0.209 ± 0.003 mL/s, 0.411 ± 0.002 mL/s, and 0.625 ± 0.006 mL/s, respectively, at the full hairspring length. The injection rates of gear set 1 (gear ratio: 0.20:1) decreased from 0.273 ± 0.001 mL/s to 0.245 ± 0.001 mL/s with a decrement of 0.003 mL/s for 10 different effective hairspring lengths (r = 0.997, p < 0.001). The injection rates of gear set 2 (gear ratio: 0.56:1) decreased from 0.519 ± 0.003 mL/s to 0.469 ± 0.003 mL/s with a decrement of 0.006 mL/s (r = 0.987, p < 0.001), and that of gear set 3 (gear ratio: 1.09:1) decreased from 0.779 ± 0.012 mL/s to 0.709 ± 0.005 mL/s with a decrement of 0.007 mL/s (r = 0.963, p < 0.001). The coefficient of variation in the injection rate measurement was 0.727 ± 0.346%. Conclusions: The MSP is a portable device that can reliably deliver a liquid agent to multiple subjects inside a clinical MRI bore during a scan.

Design of A Portable Insulin Syringe Based on Msp430 Mcu

Design of an Intelligent Insulin Injector

Flow Stabilizer on a Syringe Tip for Hand-Powered Microfluidic Sample Injection

Design and manufacture a syringe pump for intelligent injection of specific doses of contrast medicine in medical imaging applications

Development of Smart and Portable Controllable Syringe Pump System for Medical Applications

Building an Arduino-Based Open-Source Programmable Multichannel Syringe Pump: A Useful Tool for Fluid Delivery in Microfluidics and Flow Chemistry

Development, modeling, and control of a syringe-based picoliter-scale microinjection system

Design and Control of Electronic Syringe Pump using AVR Microcontroller

Technical note: 3D-printed MRI-compatible syringe pump

Design and Realization of Intelligent Infusion Monitoring System

Design of Remote Interworking Intelligent Medicine Chest Based on MSP430 Microcontroller

Continuous Drug Infusion for Diabetes Therapy: A Closed-Loop Control System Design

Development of New Jet Injector for Insulin Therapy

Development of a Micromanipulator Robot for Cell Injection with Sub-picoliter Scale

Self‐Powered Syringe Pump for Insulin Pump Therapy Based on High‐Voltage Triboelectric Nanogenerator and Dielectric Elastomer Actuator

Open-source spring-driven syringe pump with 3D-printed components for microfluidic applications

Micromotor Based Mini-Tablet for Oral Delivery of Insulin

An Intelligent Wearable Artificial Pancreas Patch Based on a Microtube Glucose Sensor and an Ultrasonic Insulin Pump

A novel multi-task software architecture applied in the intelligent insulin injector: An improved polling loop.

Hand-powered microfluidics: A membrane pump with a patient-to-chip syringe interface

Closed-Loop Diabetes Minipatch Based on a Biosensor and an Electroosmotic Pump on Hollow Biodegradable Microneedles