[Alteration of immunological parameters following CDDP-5-FU chemotherapy].

M. Tsukuda,A. Kubota,T. Yosida,K. Miyata,S. Sawaki

1988-11-01

Abstract:

What problem does this paper attempt to address?

Three-Dimensional Measurement System for Inner Surface of Long Tubular Parts Based on White Light Interference

Xuanren Rong,Zhangwei Chen,Hongfei Zu

DOI: https://doi.org/10.1109/ist59124.2023.10355659

2023-01-01

Abstract:In this paper, a 3D measurement system for the inner surface of tubular parts with large length-to-diameter ratio based on white light interference is developed. A common-path white light interferometer is built, and a side-looking probe which can obtain the reflected light of fiber end and can change the length freely is designed. In order to meet the requirements of large depth inner surface measurement, an inverted U-shaped combined device is designed and its geometric principle is described. With the aid of high-precision and large stroke 3-axis motion system, the 3D inner surface measurement is realized. The method of creating 3D point cloud, the correction method of probe center position, pose and light direction and the calibration method of system are described. The experimental results show that the system has a good inner diameter measurement accuracy, and is suitable for measuring the inner surface of long tubular parts.
Non-contact Method of Thickness Measurement for Thin-Walled Rotary Shell Parts Based on Chromatic Confocal Sensor

Sicheng Jiao,Shixiang Wang,Minge Gao,Min Xu

DOI: https://doi.org/10.1016/j.measurement.2023.113794

IF: 5.6

2023-01-01

Measurement

Abstract:In this paper, a non-contact method of thickness measurement for thin-walled rotary shell parts based on chromatic confocal sensor is presented. To obtain thickness, a flip method is applied to acquire surface profiles from both sides of the workpiece. The decentration and tilt errors of the workpiece are measured by a centering system consisting of a laser interferometer and a collimated tube. By establishing a unified reference coordinate system, the external and internal surface profiles are reconstructed and the thickness is calculated. A measurement experiment for a sapphire spherical shell workpiece was conducted on a four-axis measurement system and the result is 2.99341 mm. A wavelength-tuning interferometer and a dynamic interferometer were utilized to measure the sapphire spherical shell and an aluminum concave sphere and the results show in good agreement.
High Precision Ultrasonic Measurement Method for Thin-Walled Parts

Hao Chen,Kaipeng Ji,Wei Zhang,Chengqian Zhang,Jianzhong Fu,Peng Zhao

DOI: https://doi.org/10.1016/j.ndteint.2024.103122

IF: 4.683

2024-01-01

NDT & E International

Abstract:Thin-walled parts are extensively utilized in the aerospace industry, where over thinning defects in these parts would significantly compromise mechanical safety. Ultrasound measurement methods are commonly employed for thickness non-destructive testing. Manual calibration of reference signals is usually necessary, negatively impacting automation, robustness, and accuracy. This paper proposes a high-precision ultrasound amplitude method for thin-walled component inspection, getting rid of manual calibration. Firstly, the measured signal is preprocessed to extract the spectrum in the effective frequency range. Then, the spectrum is approximated using the asymmetrical Gaussian amplitude model to estimate the spectrum of reference signal and reflection coefficient. Moreover, initial propagation time is estimated from autocorrelation of the signal. Finally, the accurate thickness is obtained from the numerical calculation of reflection coefficient with the initial time. Simulations and experiments demonstrate that the proposed method can accurately measures metal plates as thin as 0.5mm. Compared to the traditional correlation method, it greatly improves measurement accuracy and stability, reducing them to 1/2 and 1/4 of the latter, respectively. Additionally, the proposed method also demonstrates high accuracy for curved thin plates, with an average relative error of only 0.57%. Furthermore, the method exhibits high levels of automation, robustness, and accuracy, and holds significant potential for thickness detection in thin-walled structural components.
An Imperfection Measurement System for Thin-Shell Structures Based on a Laser Displacement Meter

WU Chun-lei,ZHAO Yang

DOI: https://doi.org/10.3969/j.issn.1001-4888.2007.02.004

2007-01-01

Abstract:Buckling of thin shells is generally sensitive to geometric imperfections,so precise surveys of initial geometric imperfections are essential for high quality shell buckling experiments.This study aims to establish an experimental facility for imperfection measurement employing a laser displacement meter,which can provide fast,accurate and non-contact measurement for shell structures.The design consideration and development of the measurement system is described,including the selection of laser displacement meter,realization of rotational andlinear motion,and techniques for data acquisition and computer control.Threedimensional surveys are carefully conducted on two column-supported steel silo models using the present system,and its applicability and reliability is verified.A method for the analysis of measured imperfections utilizing the doubleFourier decomposition technique is also proposed.Results from this study provide important basis for buckling experiments of thin shell structures.
A New Boresighting Method of the Aircraft Gun Using a Laser Tracker

Qing Wang,Peng Huang,Jiangxiong Li,Yinglin Ke

DOI: https://doi.org/10.1108/sr-11-2014-740

2015-01-01

Sensor Review

Abstract:Purpose – The purpose of this paper is to propose an innovative method to extend the operating range of the laser tracking system and improve the accuracy and automation of boresighting by designing a measurement instrument. Boresighting is a process that aligns the direction of special equipment with the aircraft reference axis. Sometimes the accurate measurement and adjustment of the equipment and the aircraft are hard to achieve. Design/methodology/approach – The aircraft is moved by an automatic adjustment system which consists of three numerical control positioners. For obtaining the position of the bore axis, an instrument with two measurement points is designed. Based on the multivariate normal distribution hypothesis, an uncertainty evaluation method for the aiming points is introduced. The accuracy of the measurement point is described by an uncertainty ellipsoid. A compensation and calibration method is proposed to decrease the effect of manufacturing error and deflection error by the finite element analysis. Findings – The experimental results of the boresighting measurement prove that the proposed method is effective and reliable in digital assembly. The measurement accuracy of the angle between the bore axis and the reference axis is about ±0.004°. In addition, the measurement result is mainly influenced by the position error of the instrument. Originality/value – The results of this study will provide a new way to obtain and control the installation deviation of part in aircraft digital assembly and will help to improve the precision and efficiency. This measurement method can be applied to obtain the axis of a deep blind hole.
Form of Circumferential Weld-Induced Imperfections for Tapered-Wall Cylindrical Shell Structures

Z. Wang,Y. Zhao

DOI: https://doi.org/10.1080/19373260.2012.757206

2013-01-01

Abstract:Initial geometric imperfections have a great effect on the buckling strength of thin-walled cylindrical shells under axial compression, and the circumferential weld-induced imperfection is usually the most deleterious imperfection form. Two axisymmetric imperfection forms proposed by Rotter and Teng have widely been employed in the buckling analysis of cylindrical shells. However, the applicability of the two forms for tapered-wall cylinders needs further study, since they are derived from the elastic bending theory for long thin-walled cylinders with a constant wall thickness. This paper presents a modified form of circumferential imperfection for tapered-wall cylinders. Finite element analyses are carried out by employing the trapezoidal strain field approach to model the welding process, and the obtained circumferential depression shapes are used to evaluate the availability of the modified imperfection form. It is shown that the modified imperfection form is reasonable for any wall thickness ratio between two adjacent strakes, and the most suitable shape function, which is very close to the FE results, can be obtained by giving suitable values of the roundness in the modified form.
A Novel Radius Measurement Method for Vertical Oil Tank Based on Laser Tracking and Wall-Climbing Robot.

Hongfei Zu,Junjun Ma,Cunjun Li,Xianlei Chen,Haolei Shi,Xuwen Chen,Xiang Zhang,Zhangwei Chen

DOI: https://doi.org/10.1007/978-981-99-6501-4_30

2023-01-01

Abstract:In order to address the issue of low efficiency and poor accuracy in measuring the radius of large vertical oil tanks, a novel measurement method based on the combination of laser tracking and wall-climbing robot was proposed in this manuscript. To solve the problem of light interruption during the laser tracking measurement process, an active spherically mounted retroreflector (SMR) device that can automatically align the laser was designed. A wall-climbing robot equipped with the active target and temperature sensor was developed to crawl on the tank wall and collect four-dimensional point cloud data. And a self-written program based on the PCL point cloud processing library was adopted to fit and calculate the tank plate radius. Furthermore, multiple measurements were carried out on a vertical oil tank with a capacity of 1000 m3, and the average radius error was only 1.39 mm, which strongly verified the repeatability and feasibility of the method proposed in this manuscript. This method provides a more effective and accurate method for measuring the radius of oil tanks, and it is foreseeable that it will be a good supplement to existing methods.
Aberration Calibration in High-Na Spherical Surfaces Measurement on Point Diffraction Interferometry

Xiaoyu Chen,Yongying Yang,Chen Wang,Dong Liu,Jian Bai,Yibing Shen

DOI: https://doi.org/10.1364/ao.54.003877

IF: 1.9

2015-01-01

Applied Optics

Abstract:Systematic error in the point diffraction interferometer can significantly influence the measurement accuracy in the case that a high-numerical-aperture spherical surface is tested, in which wavefront aberrations could be observed and cannot be removed with the traditional calibration method. A calibration method, called symmetrical position aberration cancellation (SPAC) method, is proposed to remove the systematic error. With the SPAC method, the calibration needs two separate measurements with interferograms of opposite tilts and the systematic error can be reduced by averaging the test wavefronts of these two measurements. A geometrical optics model is presented for facilitating the calculation of the geometric aberrations that are introduced by the lateral deviation between the curvature center of the test surface and the center of the pinhole. Then a simulation model is built to analyze the influence of the lateral deviation and the numerical aperture of the surface under test on the systematic error. Both the computer simulation and experiments with a point diffraction interferometer (PDI) have been carried out to validate the proposed calibration method. In the final comparative experiment with a ZYGO interferometer, the PDI exhibits high precision in high-numerical-aperture spherical surfaces measurement based on the proposed calibration method. (C) 2015 Optical Society of America
Distributed Sensing Signals Of Truncated Conical Shells With Clamped-Free Boundary Conditions

Hua Li,Zhaobo Chen,Hornsen Tzou

DOI: https://doi.org/10.1115/DETC2009-87765

2010-01-01

Abstract:In aerospace structures, vehicles, civil structures, conical shells are used to support a part or connect different parts, such as spacecraft adaptors, fixtures of machine tools. This type of structures has the possibility of vibration isolation. The final purpose of the on-going research is to isolate the supported part from the vibration transferred from the other end. As a phase of the research, the present paper emphasizes on the distributed sensing signals and modal voltages of the truncated conical shell. To simulate free vibrations of supported part, one end of the truncated conical shell is clamped and the other end is free. The piezoelectric patches are attached on top skin of the shell along diagonal helical line. This paper presents an analytical procedure of sensing of truncated conical shell supporting a mass. The displacement functions satisfying the special boundary conditions are given. Based on the thin-shell theory and Donnel-Mushtari-Valsov theory, sensing equations of the piezoelectric stripes are derived. The sensing signals consist of four components, i.e. sensing signals due to meridional and circular membrane strains, meridional and circular bending strains. These components are studied separately to show their distributions to the sensing signals. Finally, a case study is carried out using a sample truncated conical shell model with laminated piezoelectric stripes.
A Semi-Analytical Method for the Dynamic Analysis of Cylindrical Shells with Arbitrary Boundaries

Xu Liang,Xing Zha,Xue Jiang,Zeng Cao,Yuhong Wang,Jianxing Leng

DOI: https://doi.org/10.1016/j.oceaneng.2019.02.074

IF: 5

2019-01-01

Ocean Engineering

Abstract:The dynamic behavior of cylindrical shells with arbitrary boundaries is studied in this paper. Love's shell theory and Hamilton's principle are employed to derive the motion equations for cylindrical shells. A semi-analytical methodology, which incorporates Durbin's inverse Laplace transform, differential quadrature method and Fourier series expansion technique, is proposed to investigate this phenomenon. The use of the differential quadrature method provides a solution in terms of the axial direction whereas the use of Durbin's numerical inversion method generates a solution in the time domain. Comparison of calculated frequency parameters to that derived from the literature illustrates the effectiveness of the method. Specifically, convergence tests indicate that the present approach has a rapid convergence, the time-history response and the Navier's solution are in great agreement. Comparisons between time-history responses derived by two shell theories show that the results fit well with each other when the thickness-radius ratios are small enough. An analysis of the influences of boundaries on the time-history response of cylindrical shells indicates that the peak displacement is closely related to the degrees of freedom of boundaries. The influences of the length-radius ratios and the thickness-radius ratios on the peak displacement are further investigated.
Geometric Modeling and Characterization of Wall Thickness for Complex Cylindrical Thin-Walled Parts With Uncertain Manufacturing Deviations

Pengyuan Chen,Shun Liu,Sun Jin,Qunfei Gu

DOI: https://doi.org/10.1115/imece2021-73185

2021-11-01

Abstract:Abstract The complex cylindrical thin-walled parts have been widely used in manufacturing field with high precision requirement of wall thickness. However, due to the existence of initial uncertain manufacturing deviations, such as blank casting errors, initial shape deviations and clamping deformations, there will be a large geometric deviation between real blank workpiece and theoretical design model. In order to solve the problem in lacking of reliable geometrical model for trajectory planning in face milling of complex cylindrical thin-walled parts, this paper proposes a method for accurate modeling and characterization of wall thickness considering the uncertain geometric deviations based on point cloud reconstruction. First, based on feature extraction and meshing process of point clouds measured with high-definition metrology both for inner and outer surfaces, subregions of each point cloud are adaptively fitted into small curved surfaces. And then NURBS surfaces are applied to connect adjacent subregions in order to form a high-precision solid model of entire workpiece. Furthermore, a characterization method of real wall thickness in milling areas is proposed. Based on the sampling mesh nodes of inner surface being the interesting points for milling areas, wall thicknesses are characterizing as distances between those sampling nodes and the outer meshed surface with an improved KD-Tree algorithm. Based on the proposed method, a meshed CAD model of real workpiece can be constructed with an error range within 0.2mm; and the wall thicknesses of milling areas can be characterized by the extracted sampling nodes. It provided an efficient methodology for geometric modeling and characterization of wall thickness of complex cylindrical thin-walled parts, which is useful for milling trajectory planning.
Ultrasonic on-machine scanning for thickness measurement of thin-walled parts: modeling and experiments

Meng Lian,Haibo Liu,Tongyu Zhang,Qile Bo,Te Li,Yongqing Wang

DOI: https://doi.org/10.1007/s00170-019-04021-5

IF: 3.563

2019-06-25

The International Journal of Advanced Manufacturing Technology

Abstract:The thickness measurement of large thin-walled part has become increasingly important to inspect the machining quality and compensate the machining errors. So far, commercial hand-held ultrasonic thickness gauges have been widely used in the wall thickness inspection of large thin-walled parts. However, the manual operation has some disadvantages such as insufficient measurement efficiency, intensive labor, and limited accuracy. To tackle these problems, an automatic thickness measuring method is supposed to be an effective approach. In this article, an ultrasonic on-machine scanning technique for thickness measurement of large thin-walled parts is proposed. First, a multi-function integrated ultrasonic thickness on-machine measuring device is innovatively designed, which enables the posture of an ultrasonic sensor to adapt to the measured surface orientation automatically. Second, the on-machine measurement model of the thickness distribution is established, which includes a measuring point coordinate extraction model and a precise thickness assessing model. Then, a scanning motion control strategy for contact ultrasonic measurement is proposed to maintain a constant pressure between the ultrasonic transducer and the workpiece during the scanning process. Finally, taking the arched part, inclined plate, and S-shaped thin-walled part as typical objects, the experimental study has been conducted using the proposed method. The experimental results show that the ultrasonic thickness on-machine measurement accuracy can be controlled within 0.04 mm, which validates the feasibility of the ultrasonic thickness on-machine scanning technique on thickness measurement of complex surface thin-walled parts.

engineering, manufacturing,automation & control systems
A Novel Method For The Micro-Clearance Measurement Of A Precision Spherical Joint Based On A Spherical Differential Capacitive Sensor

Wen Wang,He Yang,Min Zhang,Zhanfeng Chen,Guang Shi,Keqing Lu,Kui Xiang,Bingfeng Ju

DOI: https://doi.org/10.3390/s18103366

IF: 3.9

2018-01-01

Sensors

Abstract:A spherical joint is a commonly used mechanical hinge with the advantages of compact structure and good flexibility, and it becomes a key component in many types of equipment, such as parallel mechanisms, industrial robots, and automobiles. Real-time detection of a precision spherical joint clearance is of great significance in analyzing the motion errors of mechanical systems and improving the transmission accuracy. This paper presents a novel method for the micro-clearance measurement with a spherical differential capacitive sensor (SDCS). First, the structure and layout of the spherical capacitive plates were designed according to the measuring principle of capacitive sensors with spacing variation. Then, the mathematical model for the spatial eccentric displacements of the ball and the differential capacitance was established. In addition, equipotential guard rings were used to attenuate the fringe effect on the measurement accuracy. Finally, a simulation with Ansoft Maxwell software was carried out to calculate the capacitance values of the spherical capacitors at different eccentric displacements. Simulation results indicated that the proposed method based on SDCS was feasible and effective for the micro-clearance measurement of the precision spherical joints with small eccentricity.
A New Nondestructive Technique for Measuring Pressure in Vessels by Surface Waves

Hongjian Zhang,Qing He,Yong Yan

DOI: https://doi.org/10.1016/j.apacoust.2007.05.011

IF: 3.614

2008-01-01

Applied Acoustics

Abstract:Thin-walled pressure vessels are widely used in modern industry. It is important to measure pressure of the vessels. It has been proved that the velocity of ultrasonic propagation in the material could be affected by the stresses applied to it. The pressure measurement should consider the effect of temperature as the velocity of ultrasonic is affected by the temperature and thermo-stress is produced in the vessels wall. Furthermore, the propagation distance of ultrasonic is influenced by thermal deformation due to temperature changes. In consideration of these influencing factors, a modified model of pressure measurement has been developed, and according to this model, a reference method for the temperature compensation is presented. The relationship between the time delay and pressure was established through this method. The correlative time estimation method based on Hilbert–Huang Transform is presented to estimate the time delay. Therefore, a new method for measuring the pressure of thin-walled vessels nondestructively is presented. Two vessels made of different kinds of materials were used as specimens in our experiments. The results obtain from the tests are used to validate the modified model and demonstrate that the reference method is effective.
Accurate Inner Profile Measurement of a High Aspect Ratio Aspheric Workpiece Using a Two-Probe Measuring System

Peng Hu,Xin Xiong,Wen-Hao Zhang,Bing-Feng Ju,Yuan-Liu Chen

DOI: https://doi.org/10.3390/app12136628

2022-01-01

Abstract:This paper presents a novel method for inner profile measurement and geometric parameter evaluation, such as the radius of the bottom, steepness and straightness of the steep sidewall of a high aspect ratio aspheric workpiece, by utilizing a two-probe measuring system, which includes a lateral displacement gauge for the inner steep sidewall profile measurement and an axial displacement gauge for the inner deep underside profile measurement. To qualify the measurement accuracy, the systematic errors associated with the measurement procedure, including the miscalibration, misalignment and the roundness error of the gauge probes, as well as the slide motion error of the four-axis motion platform, are all evaluated and separated from the measurement results. A point cloud registration algorithm is employed to stitch the evaluated inner sidewall profile and the inner underside profile to form an entire inner profile of the workpiece. To verify the performance of the newly proposed method, the inner profile of a high aspect ratio aspheric workpiece, which has a tapered cone shape with a maximum inner radius of 40 mm, a maximum inner depth of 140 mm and a steep sidewall angle approaching 85 degrees, is measured in experiments. The measurement result is compared with that of a coordinate measuring machine (CMM), and the comparison verifies the feasibility of the proposed measurement system.
Implementation and Verification of a Dual-Probe Measurement System for Geometric Form Evaluation of a Ring-Type Cylinder

Xin Xiong,Peng Hu,Wenhao Zhang,Bing-Feng Ju,Yuan-Liu Chen

DOI: https://doi.org/10.1016/j.precisioneng.2021.12.008

IF: 3.315

2022-01-01

Precision Engineering

Abstract:This paper presents the implementation and verification of a dual-probe measurement system with a novel method and easily integrated chromatic confocal probes, for synchronous evaluation of not only the inner and outer cylindricity but also the thickness distribution of a ring-type cylinder. A pair of measuring probes mounted on a four-axis scanning stage, which is composed of XYZ-slides and a spindle, is utilized to target the two sides of the ring-type cylinder. In the developed system, to reduce the influence of the positioning errors and tilt misalignments of the confocal probes and the cylinder, alignment methods are developed. The outputs of the measuring probes are employed to accurately evaluate the geometric errors of the ring-type cylinder through performing spiral scanning while separating the Z-slide and spindle motion errors of the scanning stage based on a reversal error separation method. To verify the performance of the proposed system and method, the geometric errors of a thin-walled cylinder which has a nominal outer diameter of 50 mm, an inner diameter of 40 mm, and a length of 100 mm are evaluated in experiments. The experimental results are further compared with those by a coordinate measuring machine (CMM), and the high correspondence of the comparison results well confirm the feasibility of the implemented measurement system. Finally, measurement uncertainty analysis is conducted to demonstrate the reliability of the proposed method for the evaluation of the geometric errors of ring-type cylinders. The measurement accuracy is comparable to that of a CMM.
Analysis and Experimental Study on the Measurement of Pipe Wall Thinning by Perturbation Method

Jian MA,Ying-li ZHOU,Yang ZHAO,Qi-wu WANG,Yang JU

DOI: https://doi.org/10.14183/j.cnki.1005-6122.201706016

2017-01-01

Abstract:The inside of the metal pipe,which is short circuited at both ends,is regarded as a resonant cavity,and the thinning of the pipe wall leads to a change in the volume of the cavity.Thus,the deviation of the resonant frequency can be used to evaluate the wall thickness.Based on the theory of resonant cavity perturbation,the measurement system of pipe wall thinning is constructed,and a single coaxial cable is used to transmit and receive TM01 mode inside the pipeline to realize the detection of pipe wall thinning.The finite element model of the detection system is established,and then the parameterized sweep calculation of the degree of thinning is carried out.Correspondingly,the swept measurement system is built,and resonant frequencies versus different thicknesses are obtained.Through the comparison with the finite element calculation results,the measured data has high degree coincidence with it.And the offset of the resonant frequency increases with the thickness of the pipe wall.Therefore,the resonant cavity perturbation method can be used for the assessment of pipe wall thinning,which is an effective non-destructive testing method for in-service pipelines.
A Method Combining the MMF Technique with Ultrasonic to Inspect the Wall Thickness for Water-wall Tube

Xiaochun Song,Songling Huang,Wei Zhao,Yihua Kang

DOI: https://doi.org/10.3321/j.issn:1004-132X.2006.10.023

2006-01-01

Abstract:Wall thickness is a key index for water-wall tube inspection in power plant, in order to inspect the tube quickly and evaluate the wall thickness quantitatively, a new method combining the magnetic main flux(MMF) with ultrasonic technique was proposed. The magnetic technique was used to do full inspection and locate the flaws, and the ultrasonic was employed to implement further quantitative inspection accurately. Then, the data measured by ultrasonic transducer was used to calibrate the MMF model parameters firstly, and a function was specified to fit the relations between the wall thickness and the peak value of MMF signal, thus the wall thickness can be evaluated quickly. The experimental results demonstrate that the model used in this system has better accuracy than the statistics relation model obviously, and it is suitable for defect evaluation in real-time.
Measurement of the Wall Correction Factor of a Spherical-cylindrical Cavity Ionization Chamber

Jia-cheng HU,Xiao-yuan YANG,Yuan-di YANG,Hui ZHANG,Tie-shuan FAN,Ji-ning SUN,Fei-zeng HUANG,Jian-chang LIU,Wei-guo YE

2007-01-01

Abstract:An experimental method is used to determine the wall correction factor K wall of the spherical-cylindrical standard cavity ionization chamber, its volume is 10 cm 3, in 60Co gamma-ray air kerma measurements in the National Institute of Metrology. The factor K wall is determined by both the methods of traditional geometry thickness extrapolation and equivalent mean thickness extrapolation. The wall correction factor from extrapolation experiments for the spherical-cylindrical chambers is compared with the Monte Carlo (MC) calculations. It is concluded that the wall correction factor determined by traditional geometry thickness extrapolation method is less than 0.48% and 0.45% respectively as compared with that by the MC calculation and equivalent mean thickness. The results applying the equivalent mean thickness extrapolation and that of the MC calculations is agreed within 0.02%.
A New Design Method For Axially Loaded Thin-Walled Cylindrical Shells Based On Elasto-Plastic Buckling Analysis

Peng Jiao,Zhiping Chen,He Ma

DOI: https://doi.org/10.1115/pvp2019-93233

2019-01-01

Abstract:In engineering, thin-walled cylindrical shells subjected to axial compression load are very sensitive to geometric imperfections and are prone to buckling. However, how to reasonably take into account the influence of geometric imperfections on the load carrying capacity of thin-walled cylindrical shells is always the bottleneck of light-weight design of these structures. In this paper, four perturbation load approach (4PLA) is adopted to consider the influence of geometric imperfections. By judging the potential buckling status of cylindrical shells, a new improved design method based on 4PLA for thin-walled cylindrical shells is proposed, in which the influence of radius-to-thickness ratio, length-to-radius ratio, Young's modulus and material yield strength are systematically considered. Correspondingly, the buckling tests for two steel cylindrical shells with the same geometric and material parameters are conducted. Compared with the experimental results and other test results in open literatures, the superiority and safety of proposed method for the preliminary design of thin-walled cylindrical shells are validated.

[Alteration of immunological parameters following CDDP-5-FU chemotherapy].

Three-Dimensional Measurement System for Inner Surface of Long Tubular Parts Based on White Light Interference

Non-contact Method of Thickness Measurement for Thin-Walled Rotary Shell Parts Based on Chromatic Confocal Sensor

High Precision Ultrasonic Measurement Method for Thin-Walled Parts

An Imperfection Measurement System for Thin-Shell Structures Based on a Laser Displacement Meter

A New Boresighting Method of the Aircraft Gun Using a Laser Tracker

Form of Circumferential Weld-Induced Imperfections for Tapered-Wall Cylindrical Shell Structures

A Novel Radius Measurement Method for Vertical Oil Tank Based on Laser Tracking and Wall-Climbing Robot.

Aberration Calibration in High-Na Spherical Surfaces Measurement on Point Diffraction Interferometry

Distributed Sensing Signals Of Truncated Conical Shells With Clamped-Free Boundary Conditions

A Semi-Analytical Method for the Dynamic Analysis of Cylindrical Shells with Arbitrary Boundaries

Geometric Modeling and Characterization of Wall Thickness for Complex Cylindrical Thin-Walled Parts With Uncertain Manufacturing Deviations

Ultrasonic on-machine scanning for thickness measurement of thin-walled parts: modeling and experiments

A Novel Method For The Micro-Clearance Measurement Of A Precision Spherical Joint Based On A Spherical Differential Capacitive Sensor

A New Nondestructive Technique for Measuring Pressure in Vessels by Surface Waves

Accurate Inner Profile Measurement of a High Aspect Ratio Aspheric Workpiece Using a Two-Probe Measuring System

Implementation and Verification of a Dual-Probe Measurement System for Geometric Form Evaluation of a Ring-Type Cylinder

Analysis and Experimental Study on the Measurement of Pipe Wall Thinning by Perturbation Method

A Method Combining the MMF Technique with Ultrasonic to Inspect the Wall Thickness for Water-wall Tube

Measurement of the Wall Correction Factor of a Spherical-cylindrical Cavity Ionization Chamber

A New Design Method For Axially Loaded Thin-Walled Cylindrical Shells Based On Elasto-Plastic Buckling Analysis