Abstract:Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Ahead of Print. In this work, Fe-2Cu-0.8C-CaF2 self-lubricating composites with calcium fluoride solid lubricant (3 □ 12 wt.%) were examined for their friction and wear at 5 and 10 m/s, at 500 °C. Addition of CaF2 decreased density and hardness of composites. During sliding, materials gained weight due to oxidation. Compared to the base matrix (Fe-2Cu-0.8C), composites showed lower weight gain and lower coefficient of friction. Increase in porosity with CaF2 content increased oxidation resulting in higher weight gain and increased friction due to wear debris abrasion. Increase in speed reduced weight gain due to higher material loss. Adhesion was the dominant wear mechanism in base matrix; delamination and wear debris abrasion in composites. Temperature rise at sliding surfaces was theoretically estimated. Increase in speed increased temperature, which reduced friction due to softening and shearing of solid lubricant. Composite with 3 wt.% CaF2 showed least surface damage and 6 wt.% showed lowest coefficient of friction, i.e., lower by 16% and 10% at 5, 10 m/s than base matrix. Tribological response of the composites to a broad range of applied parameters, viz. speed, load and temperature taken from earlier works and present work is briefly summarized. The study suggests the dominant role of CaF2 content and the wear debris in altering the tribological response. Further, the stability of the developed composites at high temperature and high load conditions was also established. The study suggests that the developed composites could serve high-load and high-temperature applications for heavy machinery such as bearings, shafts and gears.

Effect of Ag addition on high-temperature self-lubricating behavior of CuNi-based composites

Microstructure evolution and properties of Cu–Ag microcomposites with different Ag content

High-temperature Tribological Properties of the Novel NiCr(MoNb)x-Ag Self-Lubricating Composite Films

Effects of rare-earth additions on the microstructure and strength of Cu–Ag composites

Influence of Ag Contents on Structure and Tribological Properties of TiSiN-Ag Nanocomposite Coatings on Ti–6Al–4V

Effect of CaF2 surface layers on the friction behavior of copper-based composite

Tribological behavior of NiCrW-based self-lubricating composites against IC10 alloy under high temperature and extremely slow sliding speed

Tribological performance of a cost-effective CrFeNiAl0.3Ti0.3 high entropy alloy based self-lubricating composite in a wide temperature range

Effect of Ag Content on Microstructure and Tribological Performance of WS2–Ag Composite Films

High-Temperature Friction and Wear Behavior of Nickel-Alloy Matrix Composites with the Addition of Molybdate

Effect of silver content on the microstructure, thermal stability and mechanical properties of CrNx/Ag nanocomposite films

Microstructure of HVOF-sprayed Ag–BaF2⋅CaF2–Cr3C2–NiCr coating and its tribological behavior in a wide temperature range (25 °C to 800 °C)

A promising high temperature self-lubricating Cu-based superalloy with coherent cuboidal L12-γʹ phases

The Effect of Solid-Liquid Composite Lubrication on the Tribological Properties of Bearing Steel

Effect of Cu content on the microstructure and properties of sintered Fe-0.8C-xCu antifriction materials

Effect of Ag Content on Friction and Wear Properties of Ag and V Co-Doped CrN Coatings at 25–700 °C

Effect of lubricant additives of Cu, Fe and bimetallic CuFe nanoparticles on tribological properties

Effect of the Ni coated graphite powders addition on the properties of the Fe-based solid self-lubricating composites

High temperature tribological response of Fe-2Cu-0.8C-CaF2 self-lubricating composites at high speeds

Influence of Ag on microstructure, mechanical properties and tribological properties of as-cast Al-33Zn-2Cu high-zinc aluminum alloy

Wear mechanism of Ag as solid lubricant for wide range temperature application in micro-beam plasma cladded Ni60 coatings