Dynamic Biaxial Compression Tests Using 4 Symmetric Input Hopkinson Bars

P. Quillery,B. Durand,M. Huang,K. Seck,H. Zhao

DOI: https://doi.org/10.1007/s11340-024-01056-y

IF: 2.794

2024-03-28

Experimental Mechanics

Abstract:Multiaxial dynamic loading situations occur in many industrial cases and multiaxial dynamic test development is thus a crucial issue.

mechanics,materials science, multidisciplinary, characterization & testing

What problem does this paper attempt to address?

Development of Structural Testing Equipment for Impact and Complex Loading

Y. Xiao

DOI: https://doi.org/10.1080/24705314.2020.1823559

2020-01-01

Journal of Structural Integrity and Maintenance

Abstract:This paper summarizes the author's work of developing various impact testing equipment and equipment for simulating complex earthquake loading for structural research. The equipment include large diameter split Hopkinson pressure bars (SHPB), large-scale drop-weight testing equipment, field-test facility of truck collisions and multi-axes seismic loading equipment. Several types of building and bridge components were tested under axial or lateral impact loads, simulating vehicular impact actions, sudden collapse and blasts. For vehicular impact action, a procedure of establishing simulative equivalent vehicular frame is proposed, making the vehicular loading tests much easier. Fundamental tests on concrete cylinders and confined concrete cylinders under high-strain rate impacts were also carried using the large-diameter equipment. Large to full-scale reinforced concrete or steel structures were also studied experimentally, using the developed equipment.
Dynamic Behavior of Reactive Powder Concrete in Split Hopkinson Pressure Bar Testing

HUANG Zheng-yu,WANG Yan,XIAO Yan,LU Fang-yun

DOI: https://doi.org/10.3969/j.issn.1000-5900.2006.02.025

2006-01-01

Abstract:Dynamic Behavior of reactive powder concrete(RPC) is studied by using a split Hopkinson pressure bar.At static state and dynamic state with different impact velocities,a series of compress tests of plain RPC,RPC containing polypropylenefiber and RPC containing steel fiber were carried out.The influence of transverse confinement on dynamic behavior was also studied.From the tests,dynamic compression strengths and the curves of stress-strain history of specimens under different strain rates wereobtained.The dynamic increase factors of specimens were obtained by comparing the dynamic compression strengths with the static one.
Dynamic Behaviour of Concrete in Biaxial Compression

D. Yan,G. Lin

DOI: https://doi.org/10.1680/macr.2007.59.1.45

IF: 2.46

2007-01-01

Magazine of Concrete Research

Abstract:Thoroughly understanding the behaviour of concrete in dynamic loading is an issue of great significance in civil engineering. However, our knowledge is limited by a lack of dynamic experiment database, especially that collected by dynamic multiaxial tests. Biaxial compressive experiments on 100 mm concrete cubes were performed using a servo-hydraulic multiaxial testing system designed and manufactured at Dalian University of Technology, China. The specimens were loaded in biaxial stress states. The lateral pressure was maintained at a fixed proportion to the axial load, with the stress ratios of 0: 1, 0.25: 1, 0.5: 1, 0.75: 1, 1: 1 respectively. The strain rate varied from 10(-5)/s to 10(-2)/s. From the test results it is revealed that the dynamic strength increases as the strain rate increases, while the damage pattern and the ultimate strength are closely related to the magnitude of lateral pressure exerted on the specimen. The shapes of stress - strain curves of the specimens at different strain rates are similar to each other. A unified formula is proposed to characterise both the effect of strain rate and the effect of stress ratio on the ultimate strength of concrete in biaxial stress states.
Compressive Impact Tests of Lightweight Concrete with 155-Mm-diameter Spilt Hopkinson Pressure Bar

Baofeng Huang,Yan Xiao

DOI: https://doi.org/10.1016/j.cemconcomp.2020.103816

IF: 9.93

2020-01-01

Cement and Concrete Composites

Abstract:High-strength, lightweight concrete materials have been widely used in many building structures, while the dynamic behaviors under high-strain-rate loading are not well understood. Two groups of high-strength, lightweight concrete specimens were cast for static and dynamic tests. The compressive strengths and densities of the specimens were 39.6 N/mm(2) and 1.3 t/m(3), respectively. Specimens with length-to-diameter ratios of 0.5 and 150-mm-diameter were tested using a 155-mm-diameter split Hopkinson pressure bar (SHPB). A copper disc was applied as the pulse shaper, and the resulting impact velocity was proven to be stable in each test scenario. The damage mode of the concrete specimens was brittle failure, and fragments with different sizes were generated after each impact. The higher the impact velocity was, the smaller the sizes of the fragments became. A representative stress-strain curve was developed based on the geometric shape of the observed curve for each specimen. The dynamic strength generally increased with the impact velocity for strain rates ranging from 40 to 140 s(-1). A new profile consisting of one parabola and two straight lines was developed to represent the experimental dynamic increase factor. The energy absorption density and fragility curves were computed to understand the energy absorption and fragility properties of the specimens.
Biaxial Tension Test of Soft Materials

Huiming Wang

DOI: https://doi.org/10.1088/1742-6596/2808/1/012040

2024-01-01

Journal of Physics Conference Series

Abstract:A specific loading machine is designed and fabricated to test the constitutive properties of soft materials by biaxial tension in this study. The finite element model under ABAQUS is launched to simulate the biaxial tension of a squared specimen, and it is verified by a theoretical model. Using the finite elements model, the effects of clamping conditions of the squared samples, including the clamping width, clamping depth, and clamping numbers, are systematically studied, which helps improve future machine design. The comparison of numerical results with experimental results is conducted by equibiaxial test and pure shear test. Finally, a novel testing procedure is suggested with the combination of numerical simulation and practical experiments to enhance the testing result.
Remote Collaborative Pseudo-dynamic Tests of a Ten-story Concrete Filled Steel Tubular Composite Frame

Fan Yun-lei,Xiao Yan,Guo Yu-rong,He Wen-hui,Li Feng-wu

2009-01-01

Abstract:A remotely cooperative hybrid dynamic testing software for multi-degree of freedom-system has been developed. It is composed of four modules, named as control center, physical tester, virtual tester, and remote observer. Utilizing the network communication platform NetSLab, control and feedback data can be transferred between the four modules. A ten-story concrete filled steel tubular composite frame was tested under different levels of earthquake excitation to evaluate the feasibility and effectiveness of the proposed testing software. The overall structure was divided into two substructures with the bottom two stories to be tested physically and the other parts to be simulated. Interactions between the two parts were also considered in the tests. The results show that the responses of the overall structure were reasonable, and the efficiency of data transmission was satisfactory.
Apparatus for measuring strength in biaxial compression

J. L. Belof,J. I. Katz

DOI: https://doi.org/10.1063/5.0059227

IF: 1.6

2022-04-01

Review of Scientific Instruments

Abstract:Most measurements of compressive strength of ductile materials have involved Hopkinson–Kolsky bars or Taylor anvils placing samples in uniaxial compression. In these geometries, strain is limited by the tendency of the sample to petal, in analogy to necking in uniaxial tension. Estimation of strength for any other form of the stress tensor requires assuming a shape of the yield surface; because data exist only for uniaxial compression, these assumptions are untested. In an imploding spherical shell, compression is biaxial, the plastic strain may not be small, and the material behavior may be nonlinear as a result of work hardening and heating by plastic work. We outline a method of measuring the strengths of materials in biaxial compression, both quasistatically and dynamically, using the compression of thin spherical shells. We suggest surrounding the shell with an annulus filled with a mixture of H 2 and Cl 2 gases whose homogeneous ignition is initiated by a flash of blue and near-ultraviolet light. Less promising approaches are described in Appendixes A–C .

instruments & instrumentation,physics, applied
Development of A Biaxial Compression Test Apparatus for Granular Materials

Lian-Wei Zhang,Jian-Min Zhang

DOI: https://doi.org/10.1063/1.4811972

2013-01-01

Abstract:A set of two-dimensional biaxial compression testing system was developed to investigate the stress-strain behavior and its change with the micro-structure of granular materials. The specimen was assembled using small metal bars with elliptical section. Load was then subjected in both horizontal and vertical directions. Three different stress paths could be realized, including constant lateral pressure, constant mean principal stress and constant principal stress ratio. A non-invasive measurement method using digital image correlation analysis was developed. The displacement of each particle in the specimen could be traced. As a result, the displacement field of each specimen and its microstructure evolution during loading process could be measured. The testing system was applied in monotonic shear tests for two-dimensional assemblies of metal bars with different size, showing its essential effectiveness for the investigation of the micro-structure change and mechanical behavior.
Biaxial Behaviour Of Plain Concrete Subjected To Dynamic Compression With Constant Lateral Stress

dongming yan,shilang xu,genda chen,hedong li

DOI: https://doi.org/10.1002/suco.201300057

2014-01-01

Structural Concrete

Abstract:This study investigates the dynamic biaxial behaviour of concrete by testing more than 60 cubic specimens on a custom-designed, servo-hydraulic-controlled machine. Each specimen was axially loaded in compression at a constant strain rate of 10(-5), 10(-4), 10(-3) or 10(-2) s(-1) while two opposite side faces were subjected to a constant confining pressure and the other two side faces were free. The confining pressure applied to each specimen was 0, 30.5, 61.0 or 91.5 % of its uniaxial compressive strength. Test results indicate that the biaxial strength of concrete increases with strain rate at a reduced slope as confining pressure increases. The failure mode of the concrete specimens was basically unaffected by the strain rate. An empirical relation for the ultimate strength of concrete in a biaxial stress state was developed taking into account the effects of both confinement and strain rate.
An electromagnetic Hopkinson bar for low wave impedance material and complex stress paths loading tests

Yingjiang Guo,Zengqiang Cao,Xiaohe Wang,Yuehaoxuan Wang,Liang Li,Lubin Huo

DOI: https://doi.org/10.1080/15376494.2024.2302917

2024-01-14

Mechanics of Advanced Materials and Structures

Abstract:The split Hopkinson bar has been widely used for testing the dynamic mechanical properties of various materials. However, there are still difficulties in ensuring stress uniformity when testing some low wave impedance materials such as soft materials and brittle materials and difficulty in achieving true multi-axial and multi-directional synchronous loading experiments and other issues. To overcome these issues, this paper uses an electromagnetic Hopkinson bar for experimental research and introduces its principle and implementation process. Finite element analysis and experimental methods were used to verify the feasibility of the electromagnetic Hopkinson bar in addressing the relevant issues. The superiority of the new device was demonstrated by its capability in performing compression experiments on two typical low wave impedance materials: polymethacrylates (PMMA) and polyurethane (PU), and two-way tension experiments on 2024 aluminum alloy. The results indicate that the electromagnetic Hopkinson bar can effectively solve the problem of uniform stress in low wave impedance materials testing, and can achieve synchronous loading of complex stress paths.

materials science, multidisciplinary,mechanics, composites, characterization & testing
Dynamic shear response of a polymer bonded explosive using a modified Hopkinson bar apparatus

P. D. Zhao,F. Y. Lu,Y. L. Lin,R. Chen,L. Lu

DOI: https://doi.org/10.1007/978-1-4614-0222-0_28

2011-01-01

Abstract: An innovative Hopkinson pressure bar system for testing the shear response of materials at high strain rates has been developed. A novel single-lap specimen of a polymer bonded explosive (PBX) is used. Instead of strain gauges mounted on the bars, one quartz force transducer is sandwiched between the clamp and the transmission bar to directly measure the weakly loading forces. A laser gap gauge is employed to monitor the shear strain of the specimen, which is based on the luminous flux method. Finite element code ANSYS is used to analyze the stress state in the specimen. Experimental results show that this new method is effective and reliable for determining the shear stress-strain responses of the soft materials at high strain rates.
Strength and Deformation Characteristics of Concrete under Dynamic Biaxial Loading

Yan Dong-ming,Lin Gao

DOI: https://doi.org/10.3969/j.issn.1000-7598.2007.09.045

2007-01-01

Rock and soil mechanics

Abstract:Compressive tests on cubic specimens were conducted at different strain rates using a servo-hydraulic multiaxial testing machine. Considerable emphasis was laid on the dynamic strength and deformation properties of concrete in biaxial stress state. The lateral pressure was kept in proportion to the main axial load with the ratio of 0:1, 0.25:1, 0.5:1, 0.75:1 and 1:1 respectively at the strain rate ranging from 10(-5)/s to 10(-2)/s. From the test results it is revealed that the dynamic strength is enhanced with the increasing of strain rate. The shear failure envelope is enlarged by 2 % - 10 % in case of the strain rate increasing by one order of the magnitude compared with that under static loading. The modulus of elasticity also increases with the increasing of strain rate. The linear part of the stress-strain curves tends to extend as far as strain rate increases, while the curvature of the nonlinear part tends to diminish. Moreover, strain rate has little influence on the fracture modes of specimens in biaxial stress states.
Technique for Combined Dynamic Compression–Shear Testing of PBXs

P. D. Zhao,F. Y. Lu,Y. L. Lin,R. Chen,J. L. Li,L. Lu

DOI: https://doi.org/10.1007/s11340-011-9534-8

IF: 2.794

2011-01-01

Experimental Mechanics

Abstract:We modify the split Hopkinson pressure bar and propose a compression–shear experimental method to investigate the dynamic behavior of polymer-bonded explosives (PBXs). The main apparatuses used include an incident bar with a wedge-shaped end and two transmission bars. We employ Y-cut quartzes with a rotation angle of 17.7° to measure the shear force and an optical system for shear strain measurement. A PBX with a density of 1.7 g/cm3 is investigated using the proposed method. Experimental results show that the specimen endures both compression and shear failure. Compression failure stress rises, and shear failure stress decreases as the strain rate increases. The sequences of shear and compression failure times are various at different strain rates. Based on the maximum shear failure criterion, we conclude that these phenomena are related to the experimental loading path.
3D continuum-discrete coupled modelling of triaxial Hopkinson bar tests on rock under multiaxial static-dynamic loads

W.R. Hu,K. Liu,D.O. Potyondy,Q.B. Zhang

DOI: https://doi.org/10.1016/j.ijrmms.2020.104448

IF: 6.849

2020-10-01

International Journal of Rock Mechanics and Mining Sciences

Abstract:Rock engineering projects at depth are frequently subjected to dynamic loadings under in-situ stress state, and the studies should be conducted to decipher the coupled effect of confining pressure and strain rate on the behaviour of rocks. The triaxial Hopkinson bar system has been applied to investigate the responses of materials to the coupled multiaxial static-dynamic loads. In this study, a three-dimensional (3D) continuum-discrete coupled method is employed to establish a numerical-based triaxial Hopkinson bar system, and the steel bars and a cubic specimen are modelled by continuum zones and bonded-particle material, respectively. Firstly, the detailed numerical modelling is performed to verify some prerequisites and uncertainties in the experiments, including stress wave propagation and attenuation in three directions, dynamic stress equilibrium, boundary effects, interfacial frictions, and controversial methodologies for applying confining pressure, by using the flat-joint model and parallel bond model. Then, both experimental tests and numerical modelling are carried out on sandstone under multiaxial pre-stress conditions (i.e., uniaxial, biaxial and triaxial compression) followed by dynamic loads. The dynamic responses of rock, including stress-strain curves, dynamic strength, energy evolutions, and damage patterns, exhibit confinement dependence, which is in good agreement with experimental observations. Under uniaxial compression, the specimens are broken into fragments by multiple fractures; while under biaxial compression, two symmetrically distributed V-shaped damage zones form near the free surfaces. Under triaxial compression, the degree of damage is substantially reduced, and microcrack localisation zones are initiated from the surface, propagate to the interior and eventually form macroscopic fractures. Moreover, a series of numerical simulations is conducted to investigate the strain rate dependence of sandstone under multiaxial load conditions. Both dynamic strength and peak lateral dynamic stresses increase with increasing strain rate. The increase of dynamic strength and failure strain becomes obvious at high strain rates with the enhancement of lateral confinement.

engineering, geological,mining & mineral processing
Deformation Of Soft Specimens In Dynamic Compression

W Chen,F Lu,Dj Frew

2000-01-01

Abstract:Dynamic material properties are essential to numerical simulations of structural responses to high rates of loading. It poses a challenge in experiment design to determine the dynamic behavior of soft materials such as rubbers. Numerical simulations using LS-DYNA show that a compressive specimen of a cylindrical geometry commonly used in metal testing on a split Hopkinson pressure bar (SHPB) behaves as a shock absorber. Homogeneous deformation cannot be achieved over the entire loading process, which leads to an invalid test. Experimental observations using a high-speed digital camera verify the numerical simulations. Therefore, modifications must be made on the conventional SHPB before valid experimental results can be obtained on soft materials.
Optimal Design, Development and Experimental Analysis of a Tension–Torsion Hopkinson Bar for the Understanding of Complex Impact Loading Scenarios

Y. Xu,J. Zhou,L. Farbaniec,A. Pellegrino

DOI: https://doi.org/10.1007/s11340-023-00942-1

IF: 2.794

2023-03-24

Experimental Mechanics

Abstract:Advanced testing methodologies and measurement techniques to identify complex deformation and failure at high strain rates have drawn increasing attention in recent years.

mechanics,materials science, multidisciplinary, characterization & testing
Hopkinson Bar Loaded Fracture Experimental Technique: A Critical Review of Dynamic Fracture Toughness Tests

Fengchun Jiang,Kenneth S. Vecchio

DOI: https://doi.org/10.1115/1.3124647

IF: 14.3

2009-08-05

Applied Mechanics Reviews

Abstract:Hopkinson bar experimental techniques have been extensively employed to investigate the mechanical response and fracture behavior of engineering materials under high rate loading. Among these applications, the study of the dynamic fracture behavior of materials at stress-wave loading conditions (corresponding stress-intensity factor rate ∼106 MPam/s) has been an active research area in recent years. Various Hopkinson bar loading configurations and corresponding experimental methods have been proposed to date for measuring dynamic fracture toughness and investigating fracture mechanisms of engineering materials. In this paper, advances in Hopkinson bar loaded dynamic fracture techniques over the past 30 years, focused on dynamic fracture toughness measurement, are presented. Various aspects of Hopkinson bar fracture testing are reviewed, including (a) the analysis of advantages and disadvantages of loading systems and sample configurations; (b) a discussion of operating principles for determining dynamic load and sample displacement in different loading configurations; (c) a comparison of various methods used for determining dynamic fracture parameters (load, displacement, fracture time, and fracture toughness), such as theoretical formula, optical gauges, and strain gauges; and (d) an update of modeling and simulation of loading configurations. Fundamental issues associated with stress-wave loading, such as stress-wave propagation along the elastic bars and in the sample, stress-state equilibrium validation, incident pulse-shaping effect, and the “loss-of-contact” phenomenon are also addressed in this review.

mechanics
A Novel Integrated Tension-Compression Design for A Mini Split Hopkinson Bar Apparatus

Ximin Chen,Zhanwei Liu,Guang He,Huimin Xie

DOI: https://doi.org/10.1063/1.4868593

2014-01-01

Abstract:A miniature integrated Split Hopkinson Bar (SHB) apparatus based on an innovative three-loading bar technique and a multi-stage electromagnetic driving technique was developed for both impact compression and tensile tests. The design principles of these techniques and the whole structure of this new device are discussed in detail. Compared to the traditional SHB apparatus which has a single-function, this new device can realize the integration of compression and tensile tests. Furthermore, due to the application of the electromagnetic driving technique, the whole structure of the SHB apparatus can be miniaturized with good reproducibility, reliability, and no noise, making it easier to move to different locations without the need for heavy gas launching systems used for some specialist tests. Under both impact compression and tensile conditions, a series of verification experiments were carried out on 2A12 aluminum alloy, proving that the new apparatus can conduct impact tension and compression tests for small specimen with high accuracy and reliability. The dynamic behavior of electrodeposited nickel fabricated by micromachining was investigated at a high strain rate of 1.2 × 10(4) s(-1) using this new setup, the obtained results indicating that the Lithographie Galanoformung Abformung (LIGA) deposited nickel is very sensitive to strain rate.
Dynamic impact testing of cellular solids and lattice structures: Application of two-sided direct impact Hopkinson bar

Tomáš Fíla,Petr Koudelka,Jan Falta,Petr Zlámal,Václav Rada,Marcel Adorna,Stefan Bronder,Ondřej Jiroušek

DOI: https://doi.org/10.1016/j.ijimpeng.2020.103767

IF: 4.592

2021-02-01

International Journal of Impact Engineering

Abstract:Direct impact testing with a Hopkinson bar is, nowadays, a very popular experimental technique for investigating the behavior of cellular materials, e.g., lattice metamaterials, at high strain-rates as it overcomes several limitations of the conventional Split Hopkinson Pressure Bar (SHPB). However, standard direct impact Hopkinson bars (DIHB) have only single-sided instrumentation complicating the analysis. In this paper, a DIHB apparatus instrumented with conventional strain-gauges on both bars (a so called Open Hopkinson Pressure Bar - OHPB) was used for dynamic impact experiments of cellular materials. Digital image correlation (DIC) is used as a tool for investigating the displacements and velocities at the faces of the bars. A straight-forward wave separation technique combining the data from the strain-gauges with the DIC is adopted to increase the experiment time window multiple times. The experimental method was successfully tested at impact velocities in a range of <math>5−30m·s−1</math> with both linear elastic and visco-elastic bars of a medium diameter. It is shown that, under certain circumstances, a simple linear elastic model is sufficient for the evaluation of the measurements with the visco-elastic bars, while no additional attenuation and phase-shift corrections are necessary. The applicability of the experimental method is demonstrated on various experiments with conventional metal foams, hybrid foams, and additively manufactured auxetic lattices subjected to dynamic compression.

engineering, mechanical,mechanics
Biaxial Testing of Thin Metal Sheets under Non-Proportional Loading Conditions

Steffen Gerke,Fabuer R. Valencia,Michael Brünig

DOI: https://doi.org/10.3390/met14040397

IF: 2.695

2024-03-29

Metals

Abstract:During the manufacturing and service of thin metal sheets, different stress states occur, often caused by non-proportional loading conditions. They can lead to localization of inelastic deformations as well as to damage and failure processes. In the present paper, a series of experiments with newly designed biaxially loaded specimens is presented to analyze the damage and failure behavior of thin ductile metal sheets under non-proportional load paths. Bands of holes with different orientation have been milled in critical regions of the specimens to localize stresses and strains. In compression tests, a special downholder is used to avoid buckling. During the loading processes, strain fields in critical regions of the specimens are monitored by digital image correlation technique. After the experiments, fracture surfaces are investigated by scanning electron microscopy showing different damage and fracture modes depending on the loading history. The experiments clearly demonstrate the efficiency of the thin specimens and the experimental program.

materials science, multidisciplinary,metallurgy & metallurgical engineering

Dynamic Biaxial Compression Tests Using 4 Symmetric Input Hopkinson Bars

Development of Structural Testing Equipment for Impact and Complex Loading

Dynamic Behavior of Reactive Powder Concrete in Split Hopkinson Pressure Bar Testing

Dynamic Behaviour of Concrete in Biaxial Compression

Compressive Impact Tests of Lightweight Concrete with 155-Mm-diameter Spilt Hopkinson Pressure Bar

Biaxial Tension Test of Soft Materials

Remote Collaborative Pseudo-dynamic Tests of a Ten-story Concrete Filled Steel Tubular Composite Frame

Apparatus for measuring strength in biaxial compression

Development of A Biaxial Compression Test Apparatus for Granular Materials

Biaxial Behaviour Of Plain Concrete Subjected To Dynamic Compression With Constant Lateral Stress

An electromagnetic Hopkinson bar for low wave impedance material and complex stress paths loading tests

Dynamic shear response of a polymer bonded explosive using a modified Hopkinson bar apparatus

Strength and Deformation Characteristics of Concrete under Dynamic Biaxial Loading

Technique for Combined Dynamic Compression–Shear Testing of PBXs

3D continuum-discrete coupled modelling of triaxial Hopkinson bar tests on rock under multiaxial static-dynamic loads

Deformation Of Soft Specimens In Dynamic Compression

Optimal Design, Development and Experimental Analysis of a Tension–Torsion Hopkinson Bar for the Understanding of Complex Impact Loading Scenarios

Hopkinson Bar Loaded Fracture Experimental Technique: A Critical Review of Dynamic Fracture Toughness Tests

A Novel Integrated Tension-Compression Design for A Mini Split Hopkinson Bar Apparatus

Dynamic impact testing of cellular solids and lattice structures: Application of two-sided direct impact Hopkinson bar

Biaxial Testing of Thin Metal Sheets under Non-Proportional Loading Conditions