Abstract:Because of their low density, high strength-to-weight ratio and high damping capacity, magnesium alloys have gained increasing applications in many fields, especially for die-cast magnesium alloys. The application of die-cast magnesium alloys in structures and repair welding of casting defects necessitates the development of welding techniques. As a high energy density thermal source, laser welding can reduce many welding defects compared with conventional welding methods, but pore formation during welding of die-cast magnesium alloys is still a severe problem that has not been solved. This paper seeks to identify the mechanism of pore formation during laser welding of die-cast magensium alloys and search for a metallurgic solution of porosity. The great tendency to pore formation in die-cast magnesium alloys is attributed to high gas content in the base metal. The characteristic of gas source in die-cast magnesium alloys and the process of pore formation during laser welding are studied by some experiments including analysis of characteristic parameters of pores (porosity, average diameter and number densities), change of densities before and after heating (350 degrees C, holding time 1 h) and pore formation tendency under different vacuo heating conditions (heating the base metal to 350 degrees C under vacuum environment of different holding time). The results show that heating increases porosity, average diameter and number densities, which lead to the reduction of bulk density. Vacuo heating before welding can reduce porosity to a great extent, and with holding time prolonging, porosity reduces. In die casting, there are molecular hydrogen and atomic hydrogen in die-cast magnesium alloys. The hydrogen gas (molecular hydrogen) in high pressure pores in the base metal expands sharply in the molten pool, and the oversaturated atomic hydrogen can also form new pores or contribute to the growth of exsisting pores. That is to say that both molecular hydrogen and atomic hydrogen contribute to the pore formation of die-cast magnesium alloys during laser welding. During vacuo heating before welding, atomic hydrogen can escape in part through diffusion, thus reducing the tendency to form pores. With holding time of vacuo heating prolonging, the amount of atomic hydrogen escaping from the base metal increases, thus porosity reduces. Adding elements, which can combine hydrogen to form hydride, may be a possible solution to pore formation in die-cast magnesium alloys. Preliminary experiments show that adding Zr to welds during welding can reduce the tendency to form pores obviously, the reason for this needs further research.

Effect of negative pressure continuous casting on hydrogen escape behavior in pure copper melt and purification mechanism

Influence and regulation of hydrogen content in pure copper rod billet during negative pressure continuous casting process

Motion behavior and removal mechanism of inclusions during negative pressure continuous casting process

Effect of Vacuum on Porosity and Mechanical Properties of High-Pressure Die-Cast Pure Copper

Optimizing the Pore Structure of Lotus-Type Porous Copper Fabricated by Continuous Casting

The Effect of Process Parameters on the Pore Structure of Lotus-Type Porous Copper Fabricated via Continuous Casting

Effect of Electromagnetic Transport Process on the Improvement of Hydrogen Porosity Defect in A380 Aluminum Alloy

Prediction method of shrinkage cavity and shrinkage porosity in solidification process under low-pressure casting

Hydrogen microporosity evolution and dendrite growth during long solidification of Al-Cu-Li alloys: Modeling and experiment

Porosity control and properties improvement of Al-Cu alloys via solidification condition optimisation in wire and arc additive manufacturing

Controlling the Electric Field Characteristics to Suppress the Clogging and Corrosion of the Continuous Casting Nozzle

The Purification of ZL114A Alloy by Means of Bubble Floatation

Effects of Process Parameters on Internal Quality of Castings During Novel Casting

Effect of Oxygen Injections on the Porosity of High Pressure Die Castings

Fabrication of Lotus-Type Porous Micro-Channel Copper by Single-Mold Gasar Technique

Effect of Direct Current Electric Field on the Clogging Behavior of Submerged Entry Nozzle During Casting of UltraLow‐Carbon Steel

Numerical simulation of shrinkage porosity defect in billet continuous casting

Optimization of Billet Tube Mold Designs for High-Speed Continuous Casting

Optimization of the Synchronous Pressurization Process for the Elimination of Double-Layer Oxide Film Defects

EXPERIMENTAL STUDY ON THE REASON OF PORE FORMATION IN LASER WELDING OF DIE-CAST MAGNESIUM ALLOY

Multiphase-field Modelling of Hydrogen Pore Evolution During Alloy Solidification