Abstract:The solid/gas eutectic unidirectional solidification process is a new kind of technology fabricating the lotus-type porous structure. Besides having the properties of large specific surface area, excellent sound absorption, penetrating performance etc. of traditional porous materials, the particularity of the lotus-type porous structure makes it has extraordinary mechanical and thermal properties. There is a great potential for lotus-type porous aluminum in the field of lightweight engineering and heat dissipation of chip owing to its low density, outstanding corrosion resistance and high thermal conductivity. However, the fabrication of lotus-type porous aluminum has always been been more difficulty than other metals. Until porous aluminum with excellent pore structure was fabricated under very small solidification rates (0.008 similar to 0.015 mm/s) and high superheat degrees of melt (240 similar to 340 K), the proper processing parameters were recognized to be essential for the coupled growth of solid/gas phases for Al-H-2 system, especially the solidification rate. In this work, a three-dimensional time-dependent model describing the evolution of single pore was established based on the theoretical analysis of mass transfer, gas bubble nucleation, pore growth, interruption and detachment. The morphology of single pore under different solidification rates were simulated during the Gasar process by using the finite difference method for Al-H-2 system. The research reveals: coupled growth of solid/gas phases can be achieved under the solidification rates from 0.15 mm/s to 0.005 mm/s. The average pore diameter which ranges from 100 pm to 1100 pm increases with decreasing the solidification rate. The pore length also increases while the pore aspect ratio is nearly a constant about 40 with decreasing the solidification rate. The simulated average pore diameter is in good agreement with the experimental values when solidification rate equals to 0.015 mm/s, and then being slightly lower than the experimental ones with decreasing the solidification rate. The diffusion of hydrogen into the melt during the solidification process is regarded as the main reason of the discrepancy between simulated and experimental average pore diameters. The maximum value of the simulated solidification rates for coupled growth of solid/gas phases in Al-H-2 system first increases from less than 0.01 mm/s to 0.15 mm/s and then being a constant, while the minimum ones increase from about 0.0001 mm/s to 0.01 mm/s with improving the overheat degree of melt and hydrogen partial pressure. By comparing the relative parameters of Al-H-2 and Cu-H-2 systems, the solubility of hydrogen is regarded to be the main parameter which determines solidification rates of coupled growth of solid/gas phases for Al-H-2 system.

Multiphase-field Modelling of Hydrogen Pore Evolution During Alloy Solidification

Hydrogen microporosity evolution and dendrite growth during long solidification of Al-Cu-Li alloys: Modeling and experiment

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Simulation of gas porosity formation and interaction with dendrite and eutectic structures during solidification of Al-Si alloys

Multiphase and multiphysics modeling of dendrite growth and gas porosity evolution during solidification

Predicting hydrogen microporosity in long solidification range ternary Al-Cu-Li alloys by coupling CALPHAD and cellular automata model

Quantifying the effects of hydrogen concentration and cooling rates on porosity formation in Al–Li alloys

Simulation for microstructure evolution of Al-Si alloys in solidification process

Phase-field model of isothermal solidification in multicomponent alloys for multiple grains

Simulation of Isothermal Solidification of Multi-Component Alloys with Phase-Field Method

Phase-Field Simulation of Non-Isothermal Dendritic Growth of Binary Alloy

Prediction of Mushy Zone Permeability of Al-4.5wt%Cu Alloy During Solidification by Phase Field Model and CFD Simulation

MODELING AND SIMULATION OF STRUCTURAL FORMATION OF POROUS ALUMINUM IN GASAR SOLIDIFICATION

Phase-Field Model of Isothermal Solidification with Multiple Grain Growth

Phase-Field Modeling of Microstructure Evolution in the Presence of Bubble During Solidification

Phase-Field Model of Isothermal Solidification of Binary Alloy with Multiple Grains

Phase-field Model Simulations of Alloy Directional Solidification and Seaweed-Like Microstructure Evolution Based on Adaptive Finite Element Method

A Phase-field model for simulating hydrogen-induced pitting corrosion with solid-solid phase transformation in the metal

Quantifying the effects of cooling rates and alloying additions on the microporosity formation in Al alloys

Phase-Field Simulation of Microsegregation and Dendritic Growth During Solidification of Hypoeutectic Al-Cu alloys

Numerical simulation of microstructure and microporosity morphology in directional solidification of aluminum-copper alloys: Effect of copper content and withdrawal rate