Abstract:The surface preparation is a prerequisite for ensuring the required properties of a diamond film formed by gas-phase deposition. The influence of the temperature and concentration of the CuSO 4 etchant on the structural and phase compositions of the surface of hard-alloy materials is considered in this work, and the structural and phase compositions of a continuous polycrystalline diamond film at its growth stages is also considered. The adhesion of the diamond films to the surface of hard-alloy materials is determined qualitatively. It is established that the treatment of the hard-alloy surface in the CuSO 4 solution at t = 23°C leads to the inhomogeneous removal of a cobalt binder with chipping WC grains and the formation of the porous structure in the surface layer of the WC–6% Co alloy. The treatment by the CuSO 4 etchant at t = –2°C provides the homogeneous etching of the Co binder over the boundaries of WC grains and the formation of a chemically homogeneous surface. The orientation growth and adhesion of the diamond film depend on the elemental composition of the WC–Co alloy surface after treatment by the CuSO 4 solution. If the treatment was performed at t sln = 23°C, then the removal of copper from the defect surface WC layer is complicated during the synthesis, which provides the multidirectional growth of diamond crystals in the film along two directions, 〈111〉 and 〈110〉, which causes critical biaxial compressive stresses (2.5 GPa) and leads to low film adhesion to the hard alloy surface. If the treatment is performed at t sln = –2°C, then the orientational growth of diamond crystals in the film occurs in one preferential crystallographic direction 〈111〉, which lowers the biaxial compressive stresses (1.7 GPa) and increases the adhesive bond of the film to the hard alloy surface. The structure imperfection calculated from the ratio of the lines of integrated intensities I 1333 / I 1580 using the Raman spectroscopy method decreases with an increase in concentration at negative temperatures and increases at positive temperatures of the CuSO 4 solution during surface preparation.

Preparation of Diamond Films with Cracked Textures on Stainless Steel Using W/W-N Film as an Interlayer

Deposition of an adherent diamond film on stainless steel using Cr/CrAlN as an interlayer

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

High adhesion diamond films deposited on stainless steel by using nanocomposite films with mosaic interface as an interlayer

Fracture Strength and Toughness of Chemical-Vapor-deposited Polycrystalline Diamond Films

Thickness-controllable diamond films deposited on stainless steel using a Cr/Cr-Si-N interlayer prepared at different N2/Ar flow ratios

Microstructural, Mechanical and Tribological Properties of Tungsten-Gradually Doped Diamond-Like Carbon Films with Functionally Graded Interlayers

Structure and Topographies of Diamond-Like Carbon Films Produced on Tungsten Pre-Implanted Stainless Steel Substrate by Plasma Immersion Ion Implantation and Deposition

Improvement of adhesion under the scratching condition for diamond film on the steel by adding a precarbonization process

Deposition of diamond film on steel substrate by precoating an intermediate layer

Mitigating residual stress of high temperature CVD diamond films on vanadium carbide coated steel

Diamond-like Carbon Film Synthesized by Ion Beam Assisted Deposition and Its Tribological Properties

Growth Features of Diamond Films on the Tungsten Carbide Surface with a Copper Sublayer

Ion Beam Assisted Deposition of Diamond-Like Carbon Onto Steel Materials: Preparation and Advantages

Structural Characters and Tribological Properties of Diamondlike Carbon Films

Preparation and Characterization of Ultrananocrystalline Diamond Films in H 2 /ar/ch 4 Gas Mixtures System with Novel Filament Structure

Interface architecture for superthick carbon-based films toward low internal stress and ultrahigh load-bearing capacity

Features of the diamond films growth on the tungsten carbide surface by a copper underlayer

Study on W Graded Doping Dlc Composite Films with Multicomponent Transition Layer

Effect of Stellite12 and NiCrBSi HVOF coatings on the tribological behavior of CrN PVD film

Substrate dilution and interface structures of tungsten coating deposited by double-glow plasma surface alloying on stainless steel substrate