Abstract:The paper presents the influence of the temperature of the sintering process on the microstructure and selected properties of boron carbide/TiB2/SiC composites obtained in situ by spark plasma sintering (SPS). The homogeneous mixture of boron carbide and 5% vol. Ti5Si3 micropowders were used as the initial material. Spark plasma sintering was conducted at 1700 °C, 1800 °C, and 1900 °C for 10 min after the initial pressing at 35 MPa. The heating and cooling rate was 200 °C/min. The obtained boron carbide composites were subjected to density measurement, an analysis of the chemical and phase composition, microstructure examination, and dry friction-wear tests in ball-on-disc geometry using WC as a counterpart material. The phase compositions of the produced composites differed from the composition of the initial powder mixture. Instead of titanium silicide, two new phases appeared: TiB2 and SiC. The complete disappearance of Ti5Si3 was accompanied by a decrease in the boron carbide content of the stoichiometry formula B13C2 and an increase in the content of TiB2, while the SiC content was almost constant. The relative density of the obtained boron carbide composites, as well as their hardness and resistance to wear, increased with the sintering temperature and TiB2 content. Unfortunately, the reactions occurring during sintering did not allow us to obtain composites with high density and hardness. The relative density was 76–85.2% of the theoretical one, while the Vickers hardness was in the range of 4–12 GPa. The mechanism wear of boron carbide composites tested in friction contact with WC was abrasive. The volumetric wear rate (Wv) of composites decreased with increasing sintering temperature and TiB2 content. The average value of coefficient of friction (CoF) was in the range of 0.54–0.61, i.e., it did not differ significantly from the value for B4C sinters.

Spark plasma sintering assisted rapid growth of titanium boride layers on titanium: Microstructures and growth kinetics

Characterization and Growth Kinetics of Borides Layers on Near-Alpha Titanium Alloys

Densification and grain growth kinetics of boron carbide powder during ultrahigh temperature spark plasma sintering

Surface evolution and growth kinetics of Ti6Al4V alloy in pack boriding

Evaluation of the Wear and Mechanical Properties of Titanium Diboride-Reinforced Titanium Matrix Composites Prepared by Spark Plasma Sintering

Spark Plasma Sintering of Pure Titanium: Microstructure and Mechanical Characteristics

Microstructure, densification and mechanical properties of in situ TiBw/Ti2AlNb composites fabricated by spark plasma sintering

Microstructural evolution in laser melted boron alloyed Ti-6Al-4V

Influence of Surface Nanocrystallization on Two-Step Pack-Boronizing of AISI 5120 Steel

Densification of uniformly small-grained BaTiO3 using spark-plasma-sintering

Spark Plasma Sintering of W-10Ti Alloys: Microstructure, Properties and Grain Growth Kinetics

Microstructure and Mechanical Behaviors of Titanium Matrix Composites Containing In Situ Whiskers Synthesized via Plasma Activated Sintering

Multi-stage spark plasma sintering to study the densification mechanisms of boron carbide

Effects of Boron Content on the Microstructure and Properties of BxC-TiB2 (x=4.5, 6.5 or 8.5) Ceramic Composites by the Reactive Spark Plasma Sintering

Effects of titanium and boron alloying with non-equimolar AlCrNbSiTi high entropy alloy nitride coatings

Densification and strengthening mechanism in spark plasma sintering of B4C–VB2 ceramics via carbide boronizing

Growth kinetics and corrosion properties of pack-borided Ti-5Al-2.5Sn alloy

Boronizing of CoCrFeMnNi High-Entropy Alloys Using Spark Plasma Sintering

Preparation of TiB2–SiC composites toughened with interlocking microstructure by self-assembled TiB2 plates

Microstructure and strengthening mechanism of boride in-situ reinforced titanium matrix composites prepared by plasma activated sintering

The Microstructure, Mechanical, and Friction-Wear Properties of Boron Carbide-Based Composites with TiB2 and SiC Formed In Situ by Reactive Spark Plasma Sintering