Abstract:High Power Impulse Magnetron Sputtering (HiPIMS) PVD deposition technology offers smoother coating enhanced mechanical properties and improved substrate-coating adhesion and has become a superior alternative to direct current magnetron sputtering (DCMS). The technology utilizes high peak power with a small pulse duration, leading to a much denser plasma in the order of 1018 m−3. This results in dense, defect-free, and high-quality smoother coatings. In this study, TiAlSiN coatings were deposited on WC-10Co (wt%) cermet using HiPIMS technology with two different TiSi contents. A pair of TiSi targets, either of compositions Ti77Si23 or of Ti66Si34, were used during the depositions along with another pair of Ti40Al60, in successive cathode-stages. The impact of Ti and Si atomic percentages on the microstructure and mechanical properties of the coatings was investigated using various techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), 3D-surface profiling, nano-indentation, Rockwell indentation-adhesion, and scratch test. The coating's thickness and deposition rate were estimated from the cross-section morphology. The results suggested that the TiAlN phase likely existed in an amorphous phase of Si3N4 in TiAlSiN coatings. As the Ti atomic percentage in the layer increased, the hardness improved, reaching up to 42 GPa (max). Additionally, the coating surface roughness decreased from 14.3 nm to 10.9 nm, and the grain size decreased from 10 nm to 9 nm. The adhesion strength observed under the Rockwell-indentation test was rated as HF1 in both cases. Furthermore, the indentation test revealed similar crack patterns, but an increase in Ti content significantly improved the coating-substrate adhesion, as confirmed by the Scratch test. The scratch test demonstrated a maximum load of 173 N during the complete delamination (Lc3) of TiAlSiN from the carbide substrate.

Effects of titanium and boron alloying with non-equimolar AlCrNbSiTi high entropy alloy nitride coatings

Mechanical performance of high-entropy (AlCrNbSiTi)N films fabricated by high-power impulse magnetron sputtering over a wide compositional window

Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS

Effect of Si contents on microstructure and mechanical characteristics of TiAlSiN thin film deposited by HiPIMS using different Ti Si target compositions

Microstructure and Wear Resistance of Laser Clad CoCrFeNiTiNbBx High Entropy Alloy Coatings

Effects of RF magnetron sputtering power on the structure and nanohardness of high-entropy alloys (TiVCrNbSiTaBY)N hard coatings

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Effects of Boron Content on Microstructure and Mechanical Properties of TiAlSiBxN Nanocomposite Films

Effects of Input Power Ratio of AlCr/Ti Target on the Microstructural and Mechanical Properties of AlTiCrN Coatings Synthesized by a High-Power Impulse Magnetron Sputtering Process

Research on Mechanical Properties and Corrosion Behavior of (Co34Fe8Cr29Ni8Si7)100−xBx High Entropy Alloy Coating

Effect of Al content on the hardness and thermal stability study of AlTiN and AlTiBN coatings deposited by HiPIMS

Mechanical, Tribological, and Corrosion Resistance Properties of (TiAlxCrNbY)Ny High-Entropy Coatings Synthesized Through Hybrid Reactive Magnetron Sputtering

Influence of CrB2 target current on the microstructure, mechanical and tribological properties of Cr–B–C–N coatings in water

Effects of B Content on Wear and Corrosion Resistance of Laser-Cladded Co-based Alloy Coatings

Structure and Properties of Two Al–Cr–Nb–Si–Ti High-Entropy Nitride Coatings

Machining Performance of Sputter-Deposited (al0.34cr0.22nb0.11si0.11ti0.22)50n50 High-Entropy Nitride Coatings

Microstructure and high-temperature oxidation resistance of in-situ Al 2 O 3 reinforced AlCrFeTiV high-entropy alloy with boron microalloying

On the Effect of Aluminum on the Microstructure and Mechanical Properties of CrN Coatings deposited by HiPIMS

On the high temperature oxidation behavior of AlCrBN/TiAlNbSiN multilayer coatings with addition of boron and silicon

Effect of Ni Content on the Microstructure, Performance, and Mechanical Properties of High-Entropy Alloy Nitride (AlCrTiMoVNi)N Coatings Produced by Cathodic Arc Evaporation

Effect of ceramic particles on microstructure and properties of CoCrMoNbTi high-entropy alloy coating fabricated by laser cladding