Abstract:Lithium metal is considered as one of the most promising anode candidates for high-energy batteries [1-3]. However, safety concerns induced by the formation of Li dendrites largely hinder the practical application of lithium-metal batteries [4]. It is anticipated that the use of non-flammable inorganic solid-state electrolytes can resolve these safety issues [5], but solid ceramic electrolytes generally suffer from poor physical contact with the electrode and poor electro-/chemical stability at the electrolyte|electrode interface [6]. Herein, we report on a thin and flexible hybrid electrolyte composed of NASICON-type Li1.3Al0.3Ti1.7(PO4)3 (LATP), a polymer binder, and a small amount of an ionic liquid-based electrolyte. To reinforce the interfacial stability between LATP and Li, we coat an ultrathin polysiloxane-based single-ion conducting polymer (PSiO) on the Li metal surface via a simple dip-coating method. The implementation of PSiO-coated Li (PSiO@Li) in symmetric PSiO@Li||PSiO@Li cells enables a substantial extension of the cycle life, yielding >2,000 h of stable lithium stripping-plating. The full-cells comprising PSiO@Li as the negative electrode, LiNi0.88Co0.09Mn0.03O2 (NCM88) as the positive electrode active material, and the aforementioned hybrid electrolyte exhibit substantially enhanced rate capability at high dis-/charge rates above 0.5C and greatly prolonged cycle life at 1C. The superior performance achieved herein is mainly attributed to: (1) the prevented direct contact between LATP and Li, thus avoiding the reduction of LATP and the formation of mixed ion-electron conducting interphases; (2) the regulated Li+ flux at the electrode|electrolyte interface, ensuring homogeneous Li+ stripping-plating; and (3) the promoted intimate contact between PSiO and Li via the formation of Si−O−Li bonds. References [1] T. Li, X.-Q. Zhang, P. Shi, Q. Zhang, Joule, 3 (2019) 2647-2661. [2] B. Horstmann, J. Shi, R. Amine, M. Werres, X. He, H. Jia, F. Hausen, I. Cekic-Laskovic, S. Wiemers-Meyer, J. Lopez, D. Galvez-Aranda, F. Baakes, D. Bresser, C.-C. Su, Y. Xu, W. Xu, P. Jakes, R.-A. Eichel, E. Figgemeier, U. Krewer, J.M. Seminario, P.B. Balbuena, C. Wang, S. Passerini, Y. Shao-Horn, M. Winter, K. Amine, R. Kostecki, A. Latz, Energy Environ. Sci., 14 (2021) 5289-5314. [3] S. Wang, P. Xiong, J. Zhang, G. Wang, Energy Storage Materials, 29 (2020) 310-331. [4] Z. Yu, Y. Cui, Z. Bao, Cell Rep. Phy. Sci., 1 (2020) 100119. [5] S. Xin, Y. You, S. Wang, H.-C. Gao, Y.-X. Yin, Y.-G. Guo, ACS Energy Lett., 2 (2017) 1385-1394. [6] A. Banerjee, X. Wang, C. Fang, E.A. Wu, Y.S. Meng, Chem. Rev., 120 (2020) 6878-6933.

Boron Nitride‐Based Release Agent Coating Stabilizes Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 /Li Interface with Superior Lean‐Lithium Electrochemical Performance and Thermal Stability

Boron Nitride‐Based Release Agent Coating Stabilizes Li1.3Al0.3Ti1.7(PO4)3/Li Interface with Superior Lean‐Lithium Electrochemical Performance and Thermal Stability

Stabilizing Solid Electrolyte-Anode Interface in Li-Metal Batteries by Boron Nitride-Based Nanocomposite Coating

Stable Interface Between Lithium and Electrolyte Facilitated by a Nanocomposite Protective Layer

Stabilizing Li1.3Al0.3Ti1.7(PO4)3|Li Metal Anode Interface in Solid‐State Batteries by Kevlar Aramid Nanofiber‐Based Protective Coating

Stabilization the Interface of NASICON-type Solid Electrolyte and Li metal by Al Interlayer

Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries

Stabilizing Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub>|Li Metal Anode Interface in Solid-State Batteries by Kevlar Aramid Nanofiber-Based Protective Coating

Engineering Ferroelectric Interlayer between Li1.3Al0.3Ti1.7(PO4)3 and Lithium Metal for Stable Solid‐State Batteries Operating at Room Temperature

Stabilized Solid Electrolyte Interphase Induced by Ultrathin Boron Nitride Membranes for Safe Lithium Metal Batteries

Highly Stable Quasi‐Solid‐State Lithium Metal Batteries: Reinforced Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 /Li Interface by a Protection Interlayer

Ultrathin single-ion conducting polymer enabling a stable Li|Li1.3Al0.3Ti1.7(PO4)3 interface

Reinforcing the Li|Li1.3Al0.3Ti1.7(PO4)3 Interfacial Stability by an Ultrathin Multifunctional Polysiloxane-Based Single-Ion Conducting Polymer

Constructing Multifunctional Interphase between Li1.4Al0.4Ti1.6(PO4)(3) and Li Metal by Magnetron Sputtering for Highly Stable Solid-State Lithium Metal Batteries

Origin and regulation of interfacial instability for nickel-rich cathodes and NASICON-type Li1+xAlxTi2−x(PO4)3 solid electrolytes in solid-state lithium batteries

Insights into the Enhanced Interfacial Stability Enabled by Electronic Conductor Layers in Solid‐State Li Batteries

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

Single-Crystal-Layered Ni-Rich Oxide Modified by Phosphate Coating Boosting Interfacial Stability of Li10 SnP2 S12 -Based All-Solid-State Li Batteries.

High-performance lithium metal batteries based on composite solid-state electrolytes with high ceramic content

Stabilizing the Interface of NASICON Solid Electrolyte Against Li Metal with Atomic Layer Deposition.

Roles of Lithium Aluminum Titanium Phosphate in Lithium Batteries