Abstract:This work constructs the electro‐chemo‐mechanical buffer layer with softer mechanics and higher ionic conductivity on the LATP surface through spontaneous reaction between the Li metal and the as‐prepared Ti‐LiF thin‐film using magnetron sputtering technology. Introducing this buffer layer fosters cross‐interface migration of Li‐ions and dissipates interfacial stress from Li metal growth, which helps suppress SSE failure and achieve long‐term interface stability. Li1.3Al0.3Ti1.7(PO4)3 (LATP) is a cost‐effective representative solid‐state electrolyte (SSE) with high ionic conductivity and has gradually become a hotspot for all‐solid‐state lithium metal batteries (ASLMBs). Nevertheless, its practicalization has been challenged by the intertwined electro‐chemo‐mechanical interface issues of Li/SSE, such as penetration of Li dendrites, poor physical contact, and poor interfacial compatibility. Thus, it is essential to design interfacial management from an electro‐chemo‐mechanical perspective to guarantee the stability of Li/SSE interface bottom‐to‐up and prolong the cyclic life of ASLMBs with higher electrochemical performance. Here, an electro‐chemo‐mechanical buffer layer with softer mechanics and higher ionic conductivity is constructed on LATP surface by the spontaneous reaction between Li metal and an as‐prepared Ti‐LiF thin film using the magnetron sputtering. Introducing an electro‐chemo‐mechanical buffer layer fosters cross‐interfacial migration of Li‐ions and dissipates interface stress from the growth of Li metal to suppress the early failure of the SSE, realizing long‐term interfacial stability. In consequence, Li[Ni0.8Co0.1Mn0.1]O2|Ti‐LiF LATP|Li ASLMBs deliver a high specific capacity of 163.1 mAh g−1 at 0.2 C, with a capacity retention ratio of 96.1% after 150 cycles. Therefore, the interfacial design from electro‐chemo‐mechanics has been proposed innovatively to open‐up a broad avenue for applying ASLMBs to next‐generation energy storage systems.

Stabilizing Li1.3Al0.3Ti1.7(PO4)3|Li Metal Anode Interface in Solid‐State Batteries by Kevlar Aramid Nanofiber‐Based Protective Coating

Stabilizing Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub>|Li Metal Anode Interface in Solid-State Batteries by Kevlar Aramid Nanofiber-Based Protective Coating

Stable Interface Between Lithium and Electrolyte Facilitated by a Nanocomposite Protective Layer

Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

Stabilization the Interface of NASICON-type Solid Electrolyte and Li metal by Al Interlayer

Constructing Multifunctional Interphase between Li1.4Al0.4Ti1.6(PO4)(3) and Li Metal by Magnetron Sputtering for Highly Stable Solid-State Lithium Metal Batteries

Stabilizing LATP Electrolyte Interface of All-Solid-State Lithium Ion Batteries Consisting of High-Voltage Cathode

Electro‐Chemo‐Mechanical Design of Buffer Layer Enhances Electrochemical Performance of All‐Solid‐State Lithium Batteries

Improving the stability of NASICON-type electrolyte with Li metal anode by interfacial modification

A Stable Matrix Assisting Highly Compatible and Maintainable Lithium‐Garnet Interface for Solid‐State Batteries

Stabilizing Solid Electrolyte-Anode Interface in Li-Metal Batteries by Boron Nitride-Based Nanocomposite Coating

Engineering Ferroelectric Interlayer between Li1.3Al0.3Ti1.7(PO4)3 and Lithium Metal for Stable Solid‐State Batteries Operating at Room Temperature

Layer-Structured Composite Solid-State Electrolyte with a Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 -Coated Separator for High-Voltage Lithium Metal Batteries by In Situ Polymerization

Insights into the Enhanced Interfacial Stability Enabled by Electronic Conductor Layers in Solid‐State Li Batteries

Stabilizing the Interface of NASICON Solid Electrolyte Against Li Metal with Atomic Layer Deposition.

Asymmetric Solid-State Lithium-Metal-Battery Electrolytes Featuring Na Superionic Conductor-Type Ceramic and Garnet-Type Ceramic Filled Composite Polymer

Tailoring of Li/LATP-PEO Interface via a Functional Organic Layer for High-Performance Solid Lithium Metal Batteries

Construction of Polyvinylidene Fluoride Buffer Layers for Li1.3Al0.3Ti1.7(PO4)(3) Solid-State Electrolytes toward Stable Dendrite-Free Lithium Metal Batteries

Progress and Perspective of Li 1 + X Al X Ti 2 ‐x ( PO 4 ) 3 Ceramic Electrolyte in Lithium Batteries

The construction of multifunctional solid electrolyte interlayers for stabilizing Li6PS5Cl-based all-solid-state lithium metal batteries